Alçak şasi dorse

FAYMONVILLE Multimax Plus Satteltieflader Hebebett

You can find our complete inventory of immediately and short-term available vehicles on our website.

Excerpt from the equipment. Full equipment list available upon request.

Gooseneck in SNT design to optimize loading deck length, approx. 3,700 mm long, rear with chamfer approx. 1,000 mm x 6°
* For tractor units: 4 x 2 and 6 x 2
* ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets
* 3 kW electro-hydraulic power unit for controlling hydraulic operations, excluding hydraulic winches. Without installation of supply connections on the tractor unit
* Outer beams of the gooseneck with mounting holes for boltable lashing rings. The first hole approx. 200 mm from the front, then every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN)
* One mounting hole in the upper rear area of the gooseneck's outer beams for a bolt-on lashing ring
* 1 pair of screw-in lashing rings included (LC 10,000 daN)
* 3 pairs of recessed lashing rings inside on the gooseneck's outer beam (LC 5,000 daN)
* 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN)
* 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN)
* On the gooseneck and rear chamfer, grating surface with 5 mm steel reinforcement
* 2-inch king pin
* Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917)
* Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m in length) between trailer and tractor unit with NATO-NATO plugs
* On the gooseneck, 1 pair of plug-in ALU side boards, approx. 400 mm high, anodized finish

LOADING AREA:
* Loading area, approx. 9,600 mm long, with rear chamfer approx. 900 mm x 6°
* Loading area behind gooseneck hydraulically height-adjustable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg
* TPMS tire pressure monitoring system in accordance with ECE R 141
* BPW axles and suspension, 1st and 2nd axle fixed, 3rd axle steered. 3rd axle with electromagnetically controlled reverse lock, activated via reverse gear and manually
* Technical axle load: 12,000 kg each
* Air suspension with lift and lower valve
* 235/75 R 17.5 3PMSF twin tires. Make at our discretion, load index 143/141J (144/144F)
* Mechanical landing legs with 2-speed gearbox and crank
* Continuous grating surface with approx. 5 mm steel reinforcement underlay, designed for point loads: – on the lift bed – on the loading area
* Painted sand coating on the deck plates of the gooseneck and in the transition areas between neck and lifting bed, between lifting bed and loading area, and between loading area and ramps
* 1 spare wheel mounting bracket under loading area on right side in front of axles
* Cut-outs in the outer frame of the loading area and lifting bed for securing straps (LC 2,000 daN)
Cgsdpfx Ajyhkquefmsn
* 11 pairs of recessed lashing rings flush in the outer frame of the loading area, foldable outwards (LC 10,000 daN): – 3 pairs in the outer frame of the lifting bed – 8 pairs in the outer frame of the loading area
* 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): – 3 pairs in the lifting bed – 8 pairs in the rear part of the loading area
* Control valves for hydraulic ramps located on the right side of the vehicle
* 1 pair of foldable mechanical rear supports with single-handed operation

HYDRAULIC LOADING RAMPS:
* 1 pair of two-part AXS steel ramps with a length of approx. 4,920 mm and a

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.