Damperli kamyon

Stas 50

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 9.700 mm, yükleme alanı genişliği: 2.350 mm, yükleme alanı yüksekliği: 2.165 mm, yükleme alanı hacmi: 50 m³, ilk tescil: 09/2008, Chassis ALU chassis, aluminium alloy 5383H34 Two fully automatically welded T-profiles (width 200 mm) Corrosion protection between steel and aluminium parts, continuous rubber strip pressure-bonded to the longitudinal members, maximum stability via integrated tipping shaft with wear-resistant, pressed-in special bushings, chassis width approx. 1,600 mm, air and electrical lines integrated in a plastic conduit Axles and Suspension, Disc Brakes Jost-disc axle units 3 x 9 tonnes with DCA air suspension, lift and lower valve, load gauge, 3rd axle automatically liftable Tyres and Wheels 6 wheels with tyres size 385/65 R 22.5 approx. 50-60% tread on silver steel rims, 11.75x22.5 ET 120 Landing Legs Mechanical support legs, load capacity 2 x 20 t, swing feet used for air suspension Brake System According to E.C. standard, two-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E system 2S/2M, with RSS (Roll Stability Support), ALU air tank Electrical System According to StVZO regulations, with two 5-chamber Aspöck LED tail lights, 24 Volt system with two 7-pin and one 15-pin socket at the front, EBS socket, with LED side marker lights, 2 clearance lights, 2 separate LED reversing lights Tipping Body / Dump Bed ALU dump body, side walls with welded vertical aluminium profiles, floor approx. 6 mm in highly wear-resistant aluminium alloy (5383H34), Brinell HB 110, front wall angled design in 4 mm ALU with reinforcing profiles for hydraulic cylinder mounting, side walls in 3 mm hard alloy, straight rear wall, automatic pneumatic (lockable) universal tailgate with pendulum and 2/3-1/3 barn door configuration, double hinge, made from 4 mm thick aluminium, 1 grain chute with water protection, wear plates fitted on side approx. 400-1,000mm x 3,000mm x 4mm Hydraulic System Hydraulic cylinder mounted at the front wall, operating pressure 150 bar, brand Edbro, with approx. 2 m hydraulic hose and 1" quick-release coupling Accessories 6 Parlok plastic mudguards with 2 Stas splash guards, 3 m aluminium ladder, reinforced and foldable underrun protection with 2 towing eyes, one foldable side underrun guard, catwalk on front wall with access ladder (left side), Djdjxf Spfjpfx Abpeku 3 swivelling ALU bows, 1 central additional bow holder, rolling tarp with aluminium tube in centre, rolling tarp system, approx. 660g/m² quality, tarp fastener with quick-action lock (no lashing straps), wheel brace, 2 chocks, toolbox type 800, continuous splash flap on underrun guard, etc. Offer and images are subject to prior sale/change.

Durumu: kullanılmış, toplam ağırlık: 42.000 kg, azami yük ağırlığı: 34.725 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 8.912 mm, yükleme alanı genişliği: 2.400 mm, yükleme alanı yüksekliği: 2.285 mm, yükleme alanı hacmi: 50 m³, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 10/2025, Üretim yılı: 2024, toplam genişlik: 2.550 mm, toplam yükseklik: 3.672 mm, Donanım: ABS, STAS 3-Axle Hardox Steel Tipper 50 cbm "X-Shape" First registration 10/2024, condition like NEW Internal dimensions (LxWxH): 8,912 x 2,350/2,450 x 2,285 mm (tapered body shape in width) Unladen weight only 7,275 kg Z-chassis, cranked design Continuous 5 mm Hardox steel HB450 floor Front wall and side walls 4/3 mm Hardox steel HB450 Sloped front wall, interior access ladder 2-wing portal doors, pneumatic remote unlocking 1 GRAIN SLIDE in right-hand door wing Reinforced roof tarpaulin with CENTRAL LOCKING HYVA tipping cylinder, Alpha type, suitable for high and low pressure Dodpfx Asvuhcqsbpsku ALU landing legs, full-load type 2x pneumatic vibrators below the body SAF axles with large disc brakes, 430 mm 1st axle LIFT AXLE with starting aid WABCO Trailer-EBS with RSS skid control WABCO Smartboard Automatic tipping lowering Lifting and lowering mechanism Tyres 385/65 R 22.5 ALCOA Dura-Bright high-gloss aluminium rims Aluminium access ladder Shovel and broom holder Toolbox on the right 4x LED reversing lights RENTING IS THE NEW BUYING! Now available from us with immediate FULL-SERVICE LEASING.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 10.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 1.900 mm, yükleme alanı hacmi: 50 m³, ilk tescil: 09/2017, Chassis light version Aluminium (15-6-12) Two fully automatically welded I-section longitudinal beams with welded cross members. Chassis width approx. 1,600 mm Axles and Suspension Disc brakes 430 mm "Off Road Version" SAF Intradisc axle units 3 x 9 t with SAF air suspension, central air bag arrangement next to the chassis longitudinal beams, 1st axle liftable with drive-off aid and manual forced lowering, Smart Board info center, lift-lower valve, 3rd axle with trailing steering, electrically lockable, Tyres and Wheels 6 wheels fitted with 385/65 R 22.5 tyres, approx. 40-50 % tread remaining, with Alcoa aluminium rims "satin" 11.75 x 22.5 ET 120, UNI-wheel bolts for aluminium rims Dksdpfsxf Sn Isx Abpju Landing Gear Mechanical version with single-side operation, 2 speeds, with swing foot for air suspension, 2x20t static load capacity Braking System According to E.C. standards, twin-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E including RSS (Roll-Stability-System), Wabco Smartboard info center, aluminium air reservoir system Electrical System According to StVZO regulations, with 2 five-chamber lamps type Aspöck Ecopoint 2, 24-volt system with 2x7- and 1x15-pin sockets, with lateral outline marker lights, 2 separate LED reversing lights at the rear. All air and electrical lines neatly installed in plastic tubing. Tipping Body/Bin Body, fully welded interior Aluminium bin, side walls made of 30 mm thick plank profiles (2-3 mm), 600 mm wide, welded, floor 8 mm thick high wear-resistant alloy (5383H34/HB 110), bulkhead 4 mm reinforced in straight version, rear wall as double swing doors in straight version with 2 half/half doors each with a grain chute, pneumatic floor vibrators underneath, rear hanger made of aluminium, swing-out, two hold-downs with rubber buffers on the tipper bin attached to the frame at the bulkhead, Hydraulic System Tipping cylinder with "cardan" mounting, 7,630 mm stroke Hydraulic cylinder mounted to the bulkhead, working pressure 220 bar, make Hyva, 220 bar with approx. 2.5 m hydraulic hose and loose half 1", tipping angle approx. 48° Accessories 6 Parlok mudguards, full-width spray flaps fitted to underrun protection, aluminium spare wheel holder, foldable lateral underrun protection right-hand side, large 860-type toolbox, approx. 3 m aluminium ladder, 3 mid-position, approx. 150 mm raised swing bars, rolling tarp with central light strip and separate reinforcements at wear points, approx. 660 g/m² quality, with rolling tarpaulin system, perimeter rubber cord in rear end of tarp with two tension hooks to fix onto the rear swing bar, catwalk on bin with access on left, side tarp lock with tensioning straps, rear tarp closure with welded-in rubber cord for water resistance, robust foldable aluminium underrun guard with two towing eyes left and right including locking pins, 2 "Clear-Pass" spray flaps on the mudguard to EC standard, etc. Offer and images non-binding.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 10.500 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.200 mm, yükleme alanı hacmi: 57 m³, ilk tescil: 12/2009, Chassis Made of aluminum Two fully automatically welded I-beam longitudinal members with welded cross members. Chassis width 1,600 mm. Axles and Suspension Disc Brakes Weightmaster DCA axle assemblies, type DCA 3 x 9 t with air suspension, air bellows centrally mounted to chassis longitudinal members, lift axle with starting aid and manual forced lowering, load pressure gauge, lifting-lowering valve, BVA brake wear indicator. Tires and Wheels 6 wheels with tires size 385/65 R 22.5, approx. 50-60% tread, with steel rims, 11.75 x 22.5 ET 120, UNI wheel bolts. Landing Gear Mechanical landing legs with two speeds, 2x 20 t support load, swing feet used for air suspension. Brake System According to E.G. standards, two-line Wabco system, spring-loaded parking brake acting on two axles, EBS-D+ system Wabco, aluminum air reservoir system. Electrical System Dedpfsxfn Azsx Abpeku In accordance with StVZO regulations, with 2 Aspöck five-chamber rear lights, 24V system with 2x7-pin and 1x15-pin sockets, with side marker lights, 1 separate halogen reversing spotlight mounted inside right side of body, 2 halogen side spotlights mounted near landing gear (at underrun protection height). Tipper Body/Aluminum Body Fully Welded Inside Aluminum trough, side walls made of 30 mm thick plank profiles (2-3 mm) welded 600 mm wide, floor 6 mm thick high wear-resistant alloy (5383H34/HB 110), front wall 4 mm reinforced straight type, rear wall as universal door, straight version with 2 wing doors split 2/3-1/3 with a grain sluice, rubber seal sealing door gap at the rear doors laterally and below, rear doors partially smooth clad with aluminum, universal door controlled automatically-pneumatically, lockable with separate lever, rear bow made of aluminum, can be swung out, two hold-down brackets with rubber buffer mounted at the tipping trough on the front wall to the frame. Hydraulic System Hydraulic cylinder mounted on the front wall with working pressure of 135 bar, manufacturer Edbro, 150 bar with 1" fixed half. Accessories 6 Parlok mudguards, aluminum spare wheel holder, right-hand side underrun protection, foldable design, 2 stainless steel toolboxes on the left, approx. 3 m aluminum ladder, 3 centrally positioned aluminum swing bows raised approx. 150 mm, additional centrally mounted bow receptacle for positioning (center and in front of rear door) of a total of 2 bows to widen the loading width, tarpaulin with central light strip and separate reinforcements in high-wear areas in approx. 660 g/m2 quality with rolling tarpaulin system, all-round rubber cord at rear closure of tarpaulin with two tension hooks to be fastened to swing bow at rear, walkway on chassis, side tarpaulin lock with tension straps, rear tarp closure with large aluminum sheet cover and roll tarp at rear with welded-in rubber seal against water ingress, robust foldable underrun guard in aluminum with two towing eyes left and right including locking pins, 2 longitudinal tensioning straps fastened inside the body, etc. Offer and photos non-binding.

Durumu: kullanılmış, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 10.550 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 1.900 mm, yükleme alanı hacmi: 50 m³, ilk tescil: 10/2014, Chassis light version Aluminum (15-6-12) Two fully automatically welded I-beam longitudinal members with welded cross members. Chassis width approx. 1,600 mm. Axles and suspension: 430 mm disc brakes, "off-road version" SAF-Intradisc axle assemblies 3 x 9 t with SAF air suspension, air bellows centrally mounted to the chassis longitudinal member, 1st axle liftable with starting aid and manual forced lowering, Smart Board info center, lift-lowering valve. Tyres and Wheels 6 wheels with tyres size 385/65 R 22.5 approx. 50% remaining tread, with Alcoa aluminum rims "satin" 11.75 x 22.5 ET 120, UNI wheel bolts for aluminum rims. Landing Gear Mechanical version with one-sided operation, 2 speeds, with swiveling foot for air suspension, 2x 20t static load capacity. Brake System Dodpfexfn Dlox Abpsku According to E.C. regulations, two-line Wabco system, spring-loaded parking brake acting on two axles, Wabco EBS-E incl. RSS (Roll Stability System), Wabco Smartboard info center, aluminum air tank system. Electrical System According to German road regulations (StVZO), with 2 five-chamber lights type Aspöck Ecopoint 2, 24-volt system with 2x7 and 1x15 pin sockets, with side marker lights, 2 separate LED reversing lights at the rear, 2 separate LED work lights on the supports. All air and electrical lines are neatly routed in plastic tubes! Tipper Body/Body – Fully Welded Interior Aluminum tipper body, side walls made of 30 mm thick plank profiles (2-3 mm), 600 mm wide and welded, floor 8 mm thick, high-wear resistant alloy (5383H34/HB 110), front wall 4 mm reinforced, straight design, rear wall as double-wing door in straight design with 2 wing doors in 2/3-1/3 configuration with a grain slide, rear hoop extension made of aluminum, two hold-downs with rubber buffers fastened from the tipper body to the frame at the front wall. Hydraulic System Tipping Ram with "Cardan" Mounting Hydraulic ram mounted at the front wall with a working pressure of 150 bar, brand Edbro, with approx. 2.5m hydraulic hose and 1" quick coupling, tipping angle approx. 48 degrees. Accessories 6 Parlok mudguards, complete splash guards across the full vehicle width fixed to side underrun protection, aluminum spare wheel carrier, foldable lateral underrun protection right side, large tool box type 860, approx. 3m aluminum ladder, 3 centrally mounted aluminum swing roof bows approx. 150 mm raised, roll tarpaulin with a central light strip and separate reinforcements in high-wear areas, approx. 660 g/m² quality with roll tarp system, all-around elastic rope at rear closure of tarp with two tension hooks fixed to rear swing bows, catwalk on the body with step on the left, side tarp closure with lashing straps, rear tarp closure with welded elastic rope for water ingress protection, robust foldable aluminum underrun protection with two towing eyes left and right incl. securing pin, 2 "Clear-Pass" splash guards on mudguards to E.C. standard, etc… Offer and images non-binding.

Durumu: yeni, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 10.636 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.300 mm, yükleme alanı hacmi: 60 m³, Chassis constructed in self-supporting aluminium design with corresponding reinforcements in the lower flange for particularly high stability and strength. Aggregate chassis made of aluminium, 140 mm frame height! (max. 39t) Axles and Suspension "Disc brake 22.5" Jost axle assemblies, 3 x 9 tonnes, with DC air suspension, lifting and lowering function, Wabco Smartboard, electronic brake pad wear indicator (BVA) for display in the tractor unit (without tractor equipment), 1st and 3rd axles separately liftable with starting aid (without tractor equipment), 3rd axle also with Optiturn, ECAS air suspension, tyre pressure monitoring system Wabco Trailerpulse with ZF rim-mounted sensors Tyres and Wheels 6 wheels with tyres size 385/65 R 22.5, manufacturer's choice, Alcoa aluminium rims DuraBright-11, 75x22.5 ET 120. Kingpin bolted into a 10 mm thick plate. Landing Legs Aluminium drop legs, 2 x 10 t support load; for air suspension, we use swivel feet. Brake System According to E.G. standard, two-line braking system, Wabco EBS electronic system with RSS (Roll Stability Support) system, spring-loaded brake system acting on two axles with control at the rear, aluminium air reservoir system, premium modulator. Electrical System According to German StVZO guidelines with 2 LED five-chamber lights, type Aspöck Europoint LED, integrated in the aluminium rear closure, 24-Volt system with 1x 5-pin and 2x 7-pin sockets, with LED side marker lights, 2 separate LED work lights at the rear, 2 LED work lights on the side by the landing legs, 1 LED work light mounted inside front left, operable from outside. Dodpfx Asfakkcebpjku Body / Tipping Body "Body internally fully welded" Bulkhead load 17,250 daN, rear and side walls 10,250 / 13,400 daN. Aluminium tipping body, side walls 30 mm thick aluminium plank profiles (2–3 mm), 600 mm wide, completely welded in with lower and upper flanges, plank profiles fully welded on the inside. Floor installed as moving floor system on 140 mm aluminium cross members, floor load approx. 7 t/m², cross members spaced accordingly close (approx. 350 mm). Aluminium front wall with 600 mm plank profile, 2–3 mm thick, straight design. Special aluminium corner profiles in beveled design, smooth rear wall in straight design with 2 aluminium swing doors 50/30 mm thick with 4 locking rods, welded in aluminium rear frame, mounted in Teflon and stainless steel bearings. Moving side wall suspended in reinforced aluminium upper flange with "Kevlar curtain" for complete emptying, side brush seals and additional Kevlar curtain on the side. Integrated discharge chute with foldable cover plate at the end of the floor, operable from the outside at the left rear. Observation window rear left, one sample slide each in the rear doors (total 2), service door front left. Hydraulic System "Cargo Floor" moving floor system integrated in the floor with hydraulically actuated aluminium profiles on aluminium square profiles with approx. 670 PE-HD glide strips, approx. 6 mm floor thickness, hydraulic stroke approx. 200 mm, fixed half couplings on the front wall, separate connection option for hydraulic line under the chassis with fixed half couplings, line size NW 21, fixed half couplings with size and type to be specified, operating pressure 190 to max. 240 bar, aluminium end pieces welded into the floor, electric control rear left with cable control in a lockable waterproof box. Accessories PVC mudguards with rubber flaps, aluminium spare wheel holder, folding alum

Durumu: yeni, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.535 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.650 mm, yükleme alanı hacmi: 93 m³, Chassis Version with reinforced continuous frame, newly manufactured superstructure in self-supporting design with corresponding reinforcements in the lower chord for particularly high stability and strength, cross members 140 mm high in reinforced design (for high ground load capacity), additional reinforcement as gusset plate in the front lower chord/vehicle frame area, chassis made of galvanized steel up to the support assembly (trailer construction max. 39,000 kg). Axles and Suspension "Disc brake 22.5" Jost (DCA) axle assemblies, 3x9 tonnes with DCA air suspension, raise and lower function, Wabco Smartboard infotainment center, electronic brake lining wear indicator (BVA) readable in the tractor unit (display), first axle with start-up aid (new EU regulation, without tractor unit equipment) (optional: 1st and 3rd axle liftable). Tyres and Wheels 6 wheels fitted with tyres size 385/65 R 22.5 of manufacturer's choice (Br-Go-Co) on silver steel rims, 11.75x22.5 ET 120. Landing Legs Mechanical landing gears with two speeds, 2x 20 tonnes load capacity with swivel foot. Brake System In accordance with EU standard; EBS electronic system Wabco with RSS (Roll-Stability-Support) and premium modulator, spring-loaded parking brake system operating on two axles with controls at the rear, ALU air reservoir system. Electrical System According to the guidelines of EU standard 91/633 and 97/28, with 2 five-chamber lamps type Aspöck Europoint 3 integrated into the aluminium rear cover, 24 Volt system with 1x 15-pin and 2x 7-pin sockets, with LED side marker lights, 2 reflective panels on the rear, position lights front 2x white, rear 2x red, 2 separate LED reversing lights integrated into the underrun protection. Superstructure / Tipper Body "Body fully welded inside" Reinforced side walls, front wall load 17,250 daN, side and rear wall 13,400/10,400 daN. Aluminium tipper body, side walls 30 mm thick ALU plank profiles (2-3 mm), 600 mm wide, fully welded with upper and lower chord, plank profiles fully welded inside, floor as moving floor system mounted on 140 mm ALU crossmembers, forklift floor load approx. 9 t/m², crossmembers closely spaced (approx. 350 mm), ALU front wall with 600 mm plank profile, 2-3 mm thick, in straight design, special ALU corner profiles in chamfered design, smooth rear wall in straight design with 2 ALU swing doors 50/30 mm thick, with 2 locking bars locked in a welded ALU rear frame, mounted with Teflon and Inox bearings, doors secured when open with one chain each side, reinforced wear plates on the side walls approx. 2,000x1,500x4 mm, fully welded, moving residue discharge wall with Kevlar tarp approx. 1,800 mm long plus side Kevlar tarp seals, service door in front wall with ladder folding inward. Dedpfx Asgcw Rmebpoku Hydraulic System "Cargo Floor" Moving Floor System Moving floor system in floor with hydraulically operated ALU profiles on ALU box section profiles with approx. 880 PE-HD sliding blocks plus anti-lifting sliding bearings, Type CF 10 mm floor version, hydraulic stroke approx. 200 mm working travel, fixed ends on front wall, separate option for connecting hydraulic lines under the vehicle with fixed couplings, line size NW 21, fixed couplings with size and type to be specified, operating pressure 190–max. 240 bar, ALU end pieces welded in moving floor, electronic controls rear left with radio control integrated in lockable waterproof box, without hydraulic hoses. Accessories 6 PVC mudguards with 2 anti-spray mud flaps,

Durumu: yeni, toplam ağırlık: 39.000 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.535 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.750 mm, yükleme alanı hacmi: 92 m³, Donanım: ABS, - Panama floor 900g - 10 mm floor thickness - V-sheets 2000x1500x4 - Service door on the front wall - 12 pairs of lashing rings in the front wall Chassis: Reinforced continuous chassis, new superstructure manufactured in self-supporting design with appropriate reinforcements in the lower chord for particularly high stability and strength, 140 mm high cross members in reinforced design Axle and suspension Disc brakes 22.5, Jost axle assemblies, 3 x 9 tons with DCA air suspension, lifting and lowering, Wabco Smartboard, electronic brake pad wear indicator (BVA), first axle with traction help (without tractor unit equipment) Tyres and wheels 6 wheels with 385/65 R 22.5 premium tyres (manufacturer optional) mounted on steel rims, 11.75x22.5, ET 120 Landing legs Mechanical landing gears, 2 x 20 t support load Brake system EBS E-System by Wabco with RSS system (Roll Stability Support) and premium modulator, spring-loaded brake system acting on two axles, operated from the rear Electrical system According to EC directives 91/633 and 97/28, with 2 Aspöck Europoint five-chamber lamps integrated in the aluminium rear end, 24V system with 1 x 15-pin and 2 x 7-pin sockets, LED side marker lights, 2 separate LED reversing lights integrated in the underrun protection Superstructure / Tipper body Superstructure fully welded inside, reinforced side walls. Aluminium tipper body, side walls made of 30 mm strong aluminium plank profiles (2-3 mm wall thickness), 600 mm wide, fully welded with lower and upper chord, plank profiles fully welded on the inside. Aluminium front wall with 600 mm plank profile, 2-3 mm wall thickness, straight design, with 2 aluminium swing doors 50/30 mm thick, with sliding residual discharge wall with Kevlar cover approx. 1,500 mm length, plus side Kevlar curtain seal Dodpfx Aofi Nmpsbpeku Hydraulic system: 'Cargo Floor' moving floor system Moving floor system in the body floor with hydraulically actuated aluminium profiles, mounted on aluminium square profiles with approx. 880 PE-HD sliding elements, CF type 8 mm floor design, fixed sections at the front wall, separate hydraulic line connection under the vehicle with fixed sections, operating pressure 190 - max. 240 bar, aluminium end pieces welded in the moving floor, without hydraulic hoses Accessories: 6 PVC fenders with 2 anti-spray mud flaps, 1 aluminium spare wheel holder, side aluminium underrun protection in foldable design, 1 plastic toolbox approx. 860x460x400 mm, 3.7 m aluminium ladder, tarpaulin approx. 660g/m^2 with tarpaulin system incl. rolling slat, optional with side tension belts or quick release, catwalk on front wall with access ladder, 3 steel hoops with swing-out and lockable fastener, aluminium protective cover with foldable hinges for lighting, etc. +590€ delivery cost Unladen weight: approx. 7,700 kg Offer and photos non-binding

Durumu: yeni, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.500 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.500 mm, yükleme alanı hacmi: 87 m³, Chassis Manufactured using self-supporting aluminum construction with appropriate reinforcements in the lower chord for particularly high stability and strength. Aggregate chassis made of aluminum, 140 mm frame height (max. 39 t), axles and suspension with disc brakes 22.5”, Jost axle units 3 x 9 tonnes with DC air suspension, lifting and lowering, Wabco Smartboard, electronic brake pad wear indicator (BVA) for display in the tractor unit (without tractor unit equipment), 1st and 3rd axle can be lifted separately with start-assist (without tractor unit equipment), 3rd axle additionally with Optiturn, ECAS air suspension. Tyres and wheels 6 wheels with tyres size 385/65 R 22.5 (manufacturer’s choice) on Alcoa aluminum rims, satin finish, 11.75x22.5 ET 120 (with steel version + approx. 120 kg). Landing gears Aluminum drop leg landing gears, make: Alu-Leg, 2 x 10 t support load, for air suspension we use swivel feet. Brake system According to E.E.C. standard, dual-line brake system, Wabco EBS E-System with RSS (Roll Stability Support), spring-actuated parking brake acting on two axles with control at the rear, aluminum air reservoirs, premium modulator. Electrical system According to StVZO regulations, with two five-chamber lights type Aspöck Europoint III integrated into the aluminum rear panel, 24-volt system with 1 x 15-pin and 2 x 7-pin sockets, with LED side marker lights, 2 work headlights at the rear, 2 LED work headlights at the sides at the height of the landing gears, 1 LED work headlight inside front left operable from outside. Body/tipper body — "Body fully welded inside" Bulkhead load 17,250 daN, rear and side walls 10,250 / 13,400 daN, aluminum tipper body, side walls 30 mm thick aluminum plank profiles (2-3 mm) 600 mm wide, fully welded with bottom and top chords, plank profiles fully welded inside! Floor as moving floor system laid on 140 mm aluminum crossmembers, floor forklift load approx. 7 t/m², closely spaced crossmembers (approx. 350 mm), aluminum bulkhead with 600 mm plank profile, 2-3 mm thick in straight design, special aluminum corner profiles in chamfered design, smooth rear wall in straight design with 2 aluminum swing doors 50/30 mm thick with 4 locking bars, fitted in a welded aluminum rear frame, mounted on Teflon and stainless steel bearings, traveling aluminum wall suspended from reinforced upper aluminum chord with "Kevlar tarp" for complete emptying, lateral brush sealing and additional Kevlar tarp at the sides, integrated discharge funnel with foldable cover plate at the rear left floor edge and operable from outside, inspection window at rear left, one sampling slider per rear door (total 2), service door on left in bulkhead. Hydraulic system "Cargo Floor" 24 board system — smooth version! Moving floor system in the base with hydraulically driven aluminum profiles on aluminum box profiles, fitted with approx. 880 PE-HD slide elements, approx. 8 mm floor thickness, hydraulic system with approx. 200 mm working stroke, fixed halves at bulkhead, separate possibility for connection of hydraulic line under the vehicle with fixed halves, line size NW 21, fixed halves to be specified in size and design, operating pressure 190–max. 240 bar, aluminum end pieces welded into the floor, actuation at the rear left with cable remote in a lockable waterproof box, without hydraulic hoses. Accessories Dkedpfx Ajgcw Riobpou PVC fenders with rubber splash guards, aluminum spare wheel holder, foldable aluminum side underrun protection, 1

Durumu: yeni, toplam ağırlık: 36.000 kg, azami yük ağırlığı: 28.320 kg, dingil konfigürasyonu: 3 dingil, yükleme alanı uzunluğu: 13.535 mm, yükleme alanı genişliği: 2.480 mm, yükleme alanı yüksekliği: 2.750 mm, yükleme alanı hacmi: 92 m³, Donanım: ABS, Chassis: Constructed with a continuous frame, newly manufactured in a self-supporting aluminum (ALU) design featuring appropriate reinforcements in the lower flange for exceptional stability and strength. Crossmembers are 140mm high and reinforced (for high floor load capacity). Additional reinforcement via gusset plate in the front lower flange/vehicle frame area. Chassis from galvanized steel up to the support structure. Axles and Suspension: Disc brakes 22.5, Jost (DCA) axle assemblies, 3x9 ton with DCA air suspension, lifting and lowering functions, Wabco Smartboard info center, electronic brake wear indicator BVA readable in the tractor unit (display). First axle with traction assist (new EC regulation, without tractor unit installation). Optionally, first and third axles liftable as per MP request. Tyres and Wheels: 6 wheels with tires, size 385/65 R 22.5 as per manufacturer's choice (Br-Go-Co), on silver steel rims, size 11.75x22.5 ET 120. King Pin: 2" bolted into a 10mm thick plate. Landing Legs: Mechanical landing gears with two speeds, 2x 20-ton support load, swing foot. Brake System: According to E.C. norms, EBS electronic system by Wabco with RSS (Roll Stability Support) and premium modulator. Spring-loaded brake system acting on two axles, controlled from the rear, ALU air reservoir system. Electrical System: According to EC Norm 91/633 and 97/28 with two five-chamber rear lamps, Aspöck Europoint type, integrated in ALU rear closure, 24V system with 1x 15-pin and 2x 7-pin sockets. LED side marker lights, two reflective plates at the rear, front position lights (2x white), rear position lights (2x red), two separate halogen reversing lights integrated in underrun protection. Superstructure/Body: Interior fully welded. Reinforced side walls, front wall load 17,250 daN, side and rear wall 13,400/10,400 daN. Aluminium tipper body, side walls of 30mm thick ALU plank profiles (2-3mm), 600mm wide, fully welded with upper and lower flange. Plank profiles fully welded inside. Floor with moving floor system laid on 140mm ALU crossmembers, forklift load approx. 9 t/m2. Crossmembers at approx. 350mm spacing for dense mounting. Special ALU corner profiles in chiseled design. Smooth rear wall, straight design, with two ALU swing doors, 50/30mm thick, with two rod locks mounted in a welded-in ALU rear frame with Teflon and stainless-steel bearings. Doors secured in opened position with lateral chains. Hard wear plates on side walls (approx. 2000x1500x4mm), fully welded. Mobile residual discharge wall with Kevlar tarpaulin, approx. 1800mm long plus lateral brushes with Kevlar seal. Service door in front wall with inward-turning ladder. Hydraulic System: Moving floor system in the floor with hydraulically operated ALU profiles on ALU square profiles with approx. 880 PE-HD sliding elements and additional anti-lifting slide bearings, Type CF 10mm floor version. Hydraulic stroke approx. 200mm. Fixed ends at the front wall. Separate hydraulic connection possibility under the vehicle with fixed halves, pipe size NW 21. Fixing half with size and design to be specified. Operating pressure 190-max. 240 Bar. ALU end sections welded into the moving floor. Electric control rear left with remote integrated in lockable watertight box. Without hydraulic hoses. Dedpfxefi Nmws Abpeku Accessories: 6 PVC mudguards with 2 anti-spray flaps, 6 PVC splash guards above the wheels, 1 ALU spare wheel holder, foldable side ALU underrun protection, one toolbox approx. 860x460x400