Alçak yükleyici

Fliegl VTS 400 RR

Further information
Chassis Low-bed Trailer
Steel welded construction
Turntable with heavy-duty ball bearing slewing ring
Foldable rear support
2 wheel chocks with holders
Side underrun protection, aluminium
Rear spray guards across the entire width
Quarter-circle mudguard in front of the 1st axle
Excavator arm recess starting above rear axles and running to the rear, approx. 1,800 mm long, approx. 650 mm wide, and approx. 150 mm deep, 2 pairs of lashing holes each rated 5 t in the excavator arm recess, located on the side of the main frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer
1 storage box recessed in the kink of the floor with lid, W=720 mm / L=520 mm / D=170 mm
1st pair of wheel wells recessed after the frame drop in the low-bed running gear area, with ramped entry, length at the bottom approx. 1,600 mm, approx. 400 mm deep. Note! The main frame is 400 mm higher in this area than the wheel well. 2nd pair of wheel wells between the axles in the low-bed section, ramped entry, length at the bottom approx. 600 mm, approx. 300 mm deep. Note! The main frame is 300 mm higher in this area than the wheel well.
Removable wheel well covers, insertable from main frame, with timber inserts.
Distance from outside main frame beam to beam in wheel well area approx. 1,280 mm
Extendable widenings to 3,000 mm, folding at the wheel well extensions (widening not at the rear chamfer and not at the bottom of the wheel wells) (Track width of machinery/vehicles to be transported must not exceed the external frame width of 2,550 mm)
Storage compartment for timber planks, centrally on or under the loading surface as per technical feasibility
Timber planks 70 mm for widening to 3,000 mm
Lashing points for low-bed trailer
1 pair of ring lashing eyes recessed at the front on the frame drop, each rated 5 t
8 pairs of lashing mushrooms recessed at the top and side in the outer frame, each rated 10 t
Bjdpfei Ri I Njx Ad Noww
2 x front on frame drop
6 x in the low-bed first lashing eye 250 mm from front and last max. 250 mm from rear, spacing between lashing eyes no greater than 1,100 mm
5 pairs of ring lashing eyes recessed into the outer frame, each rated 5 t (convertible to stake pockets)
Drawbar and turntable for trailer
Drawbar with certified 50 mm towing eye, towing eye inclined at 8°
Axles + Suspension
SAF drum brake axles
Axles/chassis laser alignment to reduce tyre wear and fuel consumption
Air suspension with independently controllable raise & lower valves at front and rear
Wheels and tyres
235/75 R 17.5
Manufacturer’s choice
Steel rims, twin-wheel arrangement, factory silver
Braking system
2-line compressed air braking system
Spring-actuated parking brake
Trailer Info Center, displays vehicle data such as axle load (not calibrated) and odometer
Axle load detection via EBS-CAN bus signal, display in cab (truck must be pre-equipped accordingly, no truck installation, not a calibrated scale)
Vehicle stability system
Duomatic coupling at front, with connecting line to tractor vehicle
EBS (Electronic Braking System) with EBS connector at front, with connection cable
Note: The trailer must only be towed by vehicles that guarantee the effectiveness of the ABS!
Electrics
24 Volt, multi-chamber LED taillights with resistor, lateral amber LED lights, licence plate LED illumination (Note: with certain towing vehicles false diagnostics may occur even though functionality is guaranteed)
2 front position lights in LED
2 rear lane marking lights in white/red

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.