Masif ahşap zımpara hattı

HOMAG SANDTEQ W-700+B-700

Working height: 900 mm
Working width: 1,350 mm
Abrasive belt change side: left
Workpiece thickness: 3 - 160 mm
Frequency-controlled feed speed: 4 - 20 m/min

Abrasive belt dimensions: 2,620 x 1,350-1,380 mm
Adjustable abrasive belt air-blast device: 5-stage adjustable

WRD WORKPIECE-CLEANING ROTOR
Workpiece cleaning unit with 16 rotating nozzles

MOBILE CONTROL TERMINAL
powerControl with powerTouch
Lasdpfxoyw Ndmo Algeh

SST SOFT STARTER
Inrush currents are limited to prevent voltage drops

GWRD BELT CLEANING PROGRAM
After activating the program, the machine automatically moves to a workpiece thickness of 10 mm and the air-blast rotors are activated. After complete cleaning of the feed belt, the machine returns to the initial value.

AAT EXTRACTION GATE CONTROL
Control of the extraction gates via the terminal (24 Volt, DC, without extraction gates)

UPS EMERGENCY POWER SUPPLY FOR BELT CONTROL 1-3 PC
Emergency power supply for abrasive belt oscillation in the event of a power failure

System consisting of:
SANDTEQ W-700, PROFI SWB735/RRE – bottom sanding
Wide belt sander with three sanding units for processing wood or wood-based workpiece surfaces.
The machine is prepared to accommodate up to two auxiliary units, such as cleaning brush, satin or structuring brush, and rotating cleaning nozzles.

Units:
I. R-UNIT
Sanding unit with automatically adjusting contact roller,
profiled steel roller, diameter 240 mm
with grain compensation
Drive motor: 37 kW
Abrasive belt speed: 25 m/s

- Automatic locking of the sanding unit for quick belt change and to increase process reliability
- Abrasive belt drives with electronic, wear-free brake
- Optical, contactless abrasive belt control
- Pneumatic belt tensioning with integrated belt edge compensation

II. R-UNIT
Sanding unit with automatically adjusting contact roller,
rubber-coated roller, diameter 240 mm
Rubber hardness: 85° Shore
with grain compensation
Drive motor: 30 kW
Abrasive belt speed: 18 m/s

III. E-UNIT
Sanding unit for accommodating a pressure beam

- Automatic locking of the sanding units for quick belt change and to increase process reliability
- Abrasive belt drives with electronic, wear-free brake
- Optical, contactless abrasive belt control
- Pneumatic belt tensioning with integrated belt edge compensation
- Protected shelf on the machine for storing additional sanding inserts

Drive motor: 22 kW
Abrasive belt speed: 2 - 18 m/s
Torque-dependent standby mode to reduce energy consumption.

ACP PNEUMATIC PRESSURE BEAM WITH SUPPORT
- Adjustable sanding pressure via pressure regulator
- Workpiece-controlled infeed and outfeed at the front and rear edge of the workpiece
- Various 80 mm wide sanding inserts with different felt hardnesses

Machine dimensions (LxWxH): 3,900 x 2,100 x 2,000 mm
Machine weight: approx. 7,500 kg

SANDTEQ B-700, PROFI SWT735/RRE – top sanding
Wide belt sander with three sanding units for processing wood or wood-based workpiece surfaces
Units as above, but with the addition of:
FBM FINISH BRUSH
Brush unit with finish brush
Bristle type: Horsehair
Diameter: 130 mm
Drive motor: 0.75 kW

Machine dimensions (LxWxH): 2,995 x 2,100 x 2,255 – 2,415 mm
Machine weight: approx. 6,500 kg

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.