Termoform maki̇nesi̇

ILLIG UA 100 4g

Durum: yenilenmiş (kullanılmış), Maximum forming area: 960 x 660 mm Minimum forming area: 210 x 170 mm Maximum sheet size: 1000 x 700 mm Minimum sheet size: 310 x 210 mm Maximum sheet thickness, manual feed: 12 mm Maximum sheet thickness, automatic feed: 10 mm Maximum tool height: 490 mm Maximum draw depth: 300 mm pos./neg. Total connected load approx.: 64.0 kW / 115 A Technical equipment: - Control system Siemens Simatic S7-300, panel OP 37 - Control cabinet with climate control - Top heating: 5 temperature control circuits via pilot emitters Crsdpfswf Dvaox Agqed - Bottom heating: 5 temperature control circuits via pilot emitters - Top heating with individual emitter switching - Bottom heating with individual emitter switching - Parallel clamping frame - Locking of the upper reduction frames via pneumatic motor - Locking of the lower reduction frames via cylinder - 4 cooling fans - Table vacuum adjustable via cascade control - Pre-blow / demoulding adjustable via cascade control - Large front opening for tool change - Sag control of film by photocell with support air - Automatic tool change system Lower table: 1. Tool clamping via vacuum 2. Tool change via pneumatically actuated ball rollers Upper punch: 1. With motorized remote adjustment for stroke limitation 2. Pneumatic quick-change tool clamping system Sheet feeding: - Automatic lifting of the film transport chain by motor - With pneumatic quick-clamping system for suction plates - Motorized centering of plastic sheets - Separate vacuum pump for embossed material Optional retrofitting pre-heating: - Top heating, pneumatically actuated, fieldwise control, emitters can be switched on/off individually by toggle switch - Bottom heating, pneumatically actuated, fieldwise control, emitters can be switched on/off individually by toggle switch - Temperature control for top and bottom heating via separate controllers integrated in BE switch cabinet (temperature cannot be set via UA control panel) Optional retrofitting for roll processing: - Cross cutter and feed rollers integrated into the feeding system - Roll stand RO 800

Durum: ikinci el, Fonksiyonellik: tamamen fonksiyonel, ILLIG Universal Forming Machine Type UA 155 4g Solo Technical Data - Siemens control system - Max. material size: 1500 x 1250 mm Crjdpfxsxlzqfj Agqsd - Max. forming area: 1450 x 1200 mm - Max. tool height: 700 mm - Max. material thickness: 12 mm - Heating capacity: 96 kW - Total power: 105 kW - Electrical protection: 160 A - Vacuum pump capacity: 250 m³/h - Compressed air requirement: 6 bar Equipment - Top heating with 5-zone control HTS (700ºC) - Bottom heating with 5-zone control HTS (500ºC) - Cooling fan D06 - Table cascade - Vacuum cascade - Top punch - Includes ILLIG cooling unit and ILLIG temperature control unit

Durum: iyi (kullanılmış), Üretim yılı: 1990, çalışma saatleri: 11.000 h, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: 1531, film genişliği: 700 mm, giriş akımı türü: Klima, toplam genişlik: 700 mm, toplam uzunluk: 3.500 mm, toplam yükseklik: 3.500 mm, giriş voltajı: 400 V, vakum pompası gücü: 3.000 W, basınçlı hava bağlantısı: 6 bar, çalışma genişliği: 700 mm, pompa kapasitesi: 100 l/dak, kalıp yüksekliği (min.): 300 mm, kontrol kabini genişliği: 1.000 mm, çalışma sıcaklığı: 650 °C, UA 100 1 g termoform makinesi, 1990, iyi çalışır durumda. Maksimum tabaka boyutu: 1000x700x10 Üst ısıtma 3 pilot yayıcı ile, alt ısıtma 1 pilot yayıcı ile. Motorlu yükseklik ayarı Üst ve alt çerçevenin hızlı kenetlenmesi Takımların alt tablaya hızlı bağlanması Crodpfst Iracex Agqjd Takımların üst tablaya hızlı bağlanması Alt film ok kontrolü Foto hücre ile kabarcıklanma Hafızaya alınabilir kabarcıklanma ve kalıptan çıkarma yoğunluğu → kademeli pnömatik valfler BUSCH 100 metre/küp vakum pompası Makine, yeni bir ILLIG UA 4 g otomatik makine ile değiştirildikten sonra durduruldu ve depolandı Sökülen ve kamyonunuza yüklenen makinenin fiyatı Gelip görmek isterseniz tekrar hizmete sokma imkanı

Durum: ikinci el, Üretim yılı: 1998, ILLIG Universal Forming Machine UA 155 4G + BE 155 P FHZ Technical Specifications: - Maximum material size: 1500 x 1250 mm - Maximum forming area: 1460 x 1210 mm - Maximum tool height: 600 mm - Maximum material thickness: 12 mm Crodoxlzrcjpfx Agqed Forming Station: - Schleicher P03 control system - Automatic loading and unloading function - Top heater: ceramic radiant heaters with 5-zone control - Bottom heater: ceramic radiant heaters with 3-zone control - Storage of programs and heating settings - Clamping frame with quick-change system - Parallel upper frame, longitudinal members for use of fixed format frames - Lower clamping frame for frame installation from below, central clamping via electric motor - Lower table pneumatic, with fast/creep speed adjustable by percentage - Upper punch with fast/creep speed adjustable by percentage - Pre-blowing automatic, adjustable by percentage - Pre-suction adjustable by percentage - Automatic demoulding adjustable by percentage - Sheet sag control via light barrier with support air - 6-fold cooling fan - Large front opening for tool change - Vacuum pump Sheet Loading: - Automatic sheet loading device - Final heater in the loading section for final or pre-heating of sheets - Motorized sheet lifter - Motorized adjustable sheet positioning - Motorized transport lifter - Motorized transport width adjustment