Çalışma platformlu yarı römork

KÖGEL 3-Achs MEGA Sattelanhänger

You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website.

The following is an excerpt from the equipment list. Complete specification available on request.

Frame:
* Standard ladder frame in lightweight steel construction with through-bolted cross members
* With pre-cambered chassis frame
* Cover plate between outer frame and longitudinal beams as tire protection for the rear wheels of the tractor unit
* Coupling plate approx. 8 mm thick, with a 2-inch kingpin according to DIN 74080 / ISO 337

Chassis:
* Axle lift for the 1st axle, without traction aid, fully automatic control, load-dependent, with switchable lowering of the lift axle in any load range
* Three-axle SAF-INTRADISC assembly, with disc brakes Ø 370 mm
* Air suspension with approx. 260 mm stroke

Vehicle Tires:
* 6 x 445/45 R 19.5, 160J tires
* 6 steel rims 19.5 x 14.00, offset approx. 120 mm (ET 120)

Chassis Attachments:
* Landing legs (manufacturer of your choice from Kögel), mechanical with compensating foot, 24 t lifting capacity. Single-sided operating control on the right in driving direction
* Side protection according to ECE-R73
* Spare wheel bracket with winch incl. 1 wheel mounting kit, installed in front of the axle assembly
* 2 brackets for 8 square tube insert stakes each, internal dimensions approx. 340 x 220 x 2,150 mm. Installed behind the axle assembly
* Waterproof plastic toolbox, internal dimensions approx. 545 x 400 x 400 mm, installed rear left in driving direction
* Fixed rear underrun protection in steel according to ECE-R58

Brake / Air Suspension System:
* EBS system 2S/2M with stability program (includes ABS/ALB function), EBS plug-in connection ISO 7638 (without connecting lines), parking brake as spring-loaded brake, external pneumatic connections as well as external EBS diagnostic connector via ISO 7638 plug connection
* Air suspension system incl. 1 lift and lowering valve, installed on the left in driving direction behind the axle assembly. Drive height is automatically adjusted
* 2 mix-up proof coupling heads at the front ISO 1728
* Steel air tanks for brake system and air supply (EN 286-2)

Kdodpfeyvxazex Adpoi
Floor:
* Panel floor approx. 30 mm thick, multi-layer glued plywood
* Floor fully sealed along the perimeter
* 8 rows of stake pocket rails for square tube insert stakes approx. 80 x 80 mm, arranged transversely to the driving direction (1 row consists of 1 section with 5 stake pockets between the outer frame and longitudinal beams and 1 section with 10 pockets between the longitudinal beams). Arrangement according to Kögel series drawing

Front Wall:
* Front wall approx. 1,800 mm high with volume corner stakes made of aluminum, riveted with aluminum hollow profiles, bolted/riveted with the frame
* 2 pairs of lashing rings (permissible lashing force 1,000 kg per ring) on the inside front wall according to EN 12640

Rear Wall:
* Folding rear wall approx. 600 mm made of aluminum hollow profiles with 3 tie rods and T-bolt locks, 2 folding steps on the inside
* Bolt-on steel corner posts at rear in sidewall height

Side Wall:
* 3 pairs of folding stakes at sidewall height
* VarioFix steel perforated outer frame
* The VarioFix steel perforated outer frame cannot be used for lashing due to other attachments
* 3 pairs of stake brackets for folding stakes on the outer frame (evenly distributed)
* 24 pairs of lashing rings on the outer frame (according to EN 12640), permissible tensile force 4,000 kg

Bu ilan otomatik olarak tercüme edildiğinden bazı çeviri hataları oluşmuş olabilir.