Brandalı açık yarı römork

KÖGEL 3-Achs-Cargo-Coil-Pritschensattelanhänger

Durumu: kullanılmış, azami yük ağırlığı: 34.200 kg, toplam ağırlık: 42.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 05/2023, bir sonraki muayene (TÜV): 06/2025, yükleme alanı uzunluğu: 13.620 mm, yükleme alanı genişliği: 2.480 mm, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment specification available upon request. Chassis * Conventional ladder-type frame in lightweight steel construction with continuous cross members * Route load max. 30 t evenly distributed over approx. 1.5 m at the centre of the payload * Coupling plate approx. 8 mm thick, fitted with a 2-inch kingpin in accordance with DIN 74080 / ISO 337 * Coil trough internal length approx. 9,000 mm (design as per VDI guideline 2700) to accommodate coils with diameters from min. 900 mm to max. 2,100 mm Running gear * Axle lift mechanism on axle 1 * Lift axle control, fully automatic, load-dependent Starting aid * Activation by pressing the brake 3 times, 30% overload up to a speed of 25 km/h * Operation at the chassis via switch * Additionally operable from the cab (requires in-cab switch – PIN 12) SAF INTRADISC three-axle assembly * With disc brakes, diameter approx. 430 mm, ET 120 * Air suspension with approx. 180 mm stroke Tyres * 6 x 385/65 R 22.5, 160J * 6 steel rims, 22.5 x 11.75, offset approx. 120 mm (ET 120) Chassis attachments * Landing gear, mechanical with compensating foot, 24 t lifting capacity, single-sided operation on right when facing forward * Spray suppression system in accordance with Regulation (EU) No. 109/2011 for three-axle assembly with 385/65 R22.5 tyres, consisting of 1 pair of quarter-circle mudguards in front of the axles, 1 pair of straight mudguards with spray flaps between 1st and 2nd axles, and 1 pair of quarter-circle mudguards with spray flaps behind the axles * Side underrun protection according to ECE-R73 * Storage for 8 square plug-in posts, internal dimensions approx. 340 x 220 x 2,150 mm, installed behind the axle assembly * 2 plastic toolboxes, waterproof, internal dimensions approx. 545 x 400 x 400 mm, installed at the rear left and rear right Brake / Air suspension system * EBS system 2S/2M with stability programme (includes ABS/ALB function) * Air suspension system incl. 1 raise/lower valve, mounted on the left in the direction of travel behind the axle assembly * Driving position adjusts automatically Floor * Fitted on both sides * Steel pallet stop strips with VarioFix hole pattern (bolted) on left and right in direction of travel, for internal width approx. 2,468 mm (loading height under outer rail reduced by approx. 20 mm) * Floor panels approx. 30 mm thick, multi-bonded plywood, cut out in coil well area * Coil well side panels clad with plywood panels approx. 18 mm thick * Floor edge sealed all round, coil trough cover made entirely of wood, with floor panels approx. 27 mm thick * Pocket holes for square plug-in posts approx. 80 x 80 mm, arrangement as per drawing A2, 2 pairs on the longitudinal beams in the 1st and 2nd positions, 8 pairs on the outer frame * 8 pairs of stake pockets in the coil trench for receiving square plug-in posts approx. 80 x 80 mm, arrangement: 1st pair at the front of the trench, 2nd – 7th pairs as per standard drawing, 8th pair at rear of trench Body * Quick-tightening device at front for side curtain with tension shafts and deflection lever Dcsdpsvl N N Tofx Aatsp * Quick-tightening device at rear for side curtain with tension shafts and ratchet * Body stability compliant with EN 12642 XL (VDI 2700), tested for a payload of approx. 27,000 kg Rear wall * Double-wing portal rear door made of aluminium, approx. 2,630 mm internal