Püskürtme kabini TM2015

Bumex Sp. z o.o. TM2015

Durum: yeni, Üretim yılı: 2026, Bir boya atölyesi ve bir hazırlık bölgesine ayrılmış iki bölgeli bir konteyner -Dış boyutlar: 6058x2438x2591 mm -İç boyutlar: 5538x2170x2485 mm - Deniz konteyneri: 20DV - Kapı: kabin kapısına entegre - Pencere: metal koruma ızgaralı - Aydınlatma: 4 LED lamba -Montaj gerektirmez - hemen kullanıma hazırdır Nljdpenbd Rrefx Aqqoh - Boyama kabini duvarı - tamamen ızgara Direksiyon - harici merkezi blok üzerinden otomatik; Güç - 380 V Tedarik: Eo3il2moj -fan - 3 kW - hava akış hızı - 0,7 m/s -hava akış hızı: 9500 m3/h -devridaim - kapalı devre Isıtma: -Riello 40G20 yağ brülörü -Isıtma süresi 10-15 dakika dkm3db -Maksimum sıcaklık 800°C Filtreler - ön filtre, renk durdurma filtresi, karton filtre, karbon filtre. Güvenlik: -Acil durdurma -Kapıda basınç kilidi -Sıcaklık izleme sistemi -hata göstergesi Ekipman: -16A soket -hava hazırlama ekibi - Pnömatik makara

Durum: yeni, Üretim yılı: 2025, Fonksiyonellik: tamamen fonksiyonel, toplam yükseklik: 5.600 mm, toplam uzunluk: 11.200 mm, toplam genişlik: 5.100 mm, giriş akımı türü: trifaze, garanti süresi: 24 aylar, iç yükseklik: 4.970 mm, iç uzunluk: 11.000 mm, sıcaklık: 80 °C, iç genişlik: 5.000 mm, hava ihtiyacı: 52.000 m³/saat, giriş voltajı: 380 V, ısıtma kapasitesi: 250 kW (339,91 bg), güç: 45 kW (61,18 bg), yakıt: sıvılaştırılmış petrol gazı (LPG), giriş frekansı: 50 Hz, enerji tüketimi: 45 kWh, izolasyon kalınlığı: 50 mm, nominal güç: 250 kW (339,91 bg), maks. sac kalınlığı çelik: 2 mm, Donanım: aydınlatma, * Air Treatment Unit: The air treatment unit is a recirculation system that supplies the cabin with filtered fresh air while extracting used air during the painting process. It heats the air to 60°C, mixes 10% fresh air with the extracted air via an automatic multi-damper system, and reheats the air before it is returned to the cabin. The air is heated by a burner and a heat exchanger, both made of high-quality 304 stainless steel and located within the fresh air unit. During painting, the air is filtered twice (by front and ceiling filters) before entering the cabin. The contaminated air is also filtered twice (by intake and exhaust filters) before exiting through the exhaust unit. Air treatment units are insulated like the side panels to minimize heat loss and are protected from potential vibrations and noise by rubber seals on the covers. The exhaust air is regulated by a flap in the air outlet duct, helping to control the internal pressure of the cabin. *OPERATING PRINCIPLES OF THE CABIN: Processes in the cabin are controlled via a control panel, which manages the following steps: *PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and routed through front filters before reaching the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (overspray arrestors) capture paint particles, and the air passes through final exhaust filters before being discharged. *FLASH-OFF PROCESS: After painting, the cabin continues to operate for approximately 15 minutes to remove residual solvents and thinners. During this phase, fresh air from outside circulates through the cabin. *DRYING PROCESS: In this phase, 80% of the air circulating through the cabin is heated to 60°C and directed into the cabin via a distributor. As 20% of the solvents are released during drying, these are expelled with the air. Industrial paints are typically dried at 60°C, but the cabin temperature can be adjusted via the control panel as needed. *COOLING PROCESS: After the 30-minute drying process, the coil is deactivated through the control panel, the pneumatic flap closes, and the extraction unit starts again. During the 5-minute cooling phase, fresh air from outside circulates through the cabin, after which the system stops automatically. Nlsdpfx Aqjwzl Hxsqeh ELECTRICAL AND ELECTRONIC EQUIPMENT: These control cabinets manage the functions and operation of all machines and devices integrated into the cabin. The control panel is constructed from durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical equipment and control panel: • The control panel contains essential components such as circuit breakers, fuses, signal lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation when needed. • Operating equipment runs on 380 V 50 Hz, while control devices operate on 220 V.

Üretim yılı: 2006, durum: işlem için hazır (kullanılmış), MAKOR GEMINI 56 zımpara kafalı kenar püskürtme makinesi satıyorum, üretim yılı 2006. Püskürtme ve cilaya zarar vermeden kendinden pompalı sistem ile 2 Bölgeli vakumlu boyama 2 Bölgeli UV-Kurutma 2 adet. köşe zımparalama üniteleri döner Malzeme hemen kurur ve kullanılabilir! Njdpeim Eyxofx Aqqjlh Çok iyi durumda. Hemen müsait. Kontrol etmek mümkün.