Kullanılmış Goldhofer Stz-Vl4, 4 Achs Teletieflader, Tiefbett, satın al (74.908)

Durum: ikinci el, azami yük ağırlığı: 44.980 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 09/2024, bir sonraki muayene (TÜV): 09/2025, toplam genişlik: 2.550 mm, Donanım: ABS, Our entire fleet of vehicles, including immediately and soon available models, can be found on our website. Dodpjlthgusfx Apcswa Selection of features. Complete specifications available on request. Chassis, stepped frame: * Special steel frame made from high-strength fine-grained steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle layout. Wheel covers above the axles with spray-suppression * All steel parts sandblasted * Side underrun protection made of anodised aluminum fitted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area to enable the greatest possible low-bed length in combination with AluLeg support legs instead of telescopic landing gears, max. rear swing clearance of the tractor unit approx. 2,100 mm Special superstructure with extendable rear stanchions * Self-supporting aluminum roof bow/profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear stanchions extendable to approx. 4,200 mm * Three sliding stanchions per side with rubber spring relief * Additional middle stanchion lockings in the roof bow and stowage position, actuated by pull cable and spring latch * Mechanically adjustable lifting roof, lift height approx. 400 mm, operable from both sides or one-sided without opening the opposite side or doors * Additional height adjustment approx. 480 mm in approx. 40 mm increments via stanchion adjustment * Front overlap at the bulkhead for driving under tarpaulin up to overall height approx. 4,400 mm * Four rows of approx. 150 mm stackable aluminum slats per side, 450 mm pockets at the bottom, four rows of single pockets above * Only three rows of plug-in slats in the upper deck. Spacings evenly distributed Floor * Approx. 27 mm special water-resistant bonded beech multiplex panels, rough surface * Steel sheeting in the wheel arch area * Suitable for forklift traffic according to DIN ? standard * Outer frame flush finish Brakes * WABCO air brake system with EBS according to EC Directive 71/320 EEC including PREV (Park Release Safety Valve) * Spring-type parking brake cylinders * WABCO Smart Board with odometer and axle load display Axles * 4 x 10,000 kg SAF/Sauer axles with drum brakes, low-loader version * Air suspension with lifting and lowering function, total travel approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical locking Twin tires * 235/75 R 17.5, -16-fold, incl. spare wheel holder, without spare wheel Paintwork * Chassis RAL 3002 red, single color * Middle stanchions, axles KTL coated black * Corner stanchions hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver * Bodywork in single-tone RAL color Special equipment included * ECAS air suspension, operation on the trailer * Oversize signage front and rear, galvanized, stepless telescoping with marker lights incl. bases for revolving beacons (small plates) * Additional external unlocking for sliding tarpaulin frame * 4 stanchion adapters for special outer frame profile, for locking the middle stanchions arbitrarily * PVC sliding tarpaulin, color similar to RAL 9006 silver * Translucent roof tarpaulin, extra-wide and extra-high version, flat hooks, tarpaulin folds, closures with ratchet/OCS * Rear left telescoping base for revolving beacon incl. light * Outer frame for machinery transport with approx. 64 lashing points in 2,000 kg, 3,000 kg, and 10,000 kg versions, according to construc

Durum: ikinci el, dingil konfigürasyonu: 3 aks, ilk tescil: 05/2008, * Uzatılabilir * Takip kontroll aksı * Hidrolik yükleme rampaları Dsdpox I Uyhofx Apcowa * Havalı süspansiyon -----Dahili araç numarası: 11555----Hatalar ve ara satış hakkı saklıdır WhatsApp desteği mevcut! Araçla ilgili sorularınız veya daha fazla bilgi için bize WhatsApp üzerinden kolayca ulaşabilirsiniz. WhatsApp Almanca, İngilizce -- WhatsApp Almanca, İngilizce, Arapça

Durum: ikinci el, kilometre: 195.597 km, güç: 316 kW (429,64 bg), ilk tescil: 05/2020, yakıt türü: dizel, toplam ağırlık: 32.000 kg, dingil konfigürasyonu: 3 aks, bir sonraki muayene (TÜV): 05/2026, renk: beyaz, vites türü: otomatik, emisyon sınıfı: Euro 6, yükleme alanı hacmi: 13 m³, yükleme alanı uzunluğu: 5.600 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 1.000 mm, Donanım: ABS, klima, navigasyon sistemi, park ısıtıcısı, * Sun visor * ABS (Anti-lock Braking System) * Auxiliary heater * Cruise control * Hill start assist * Electric window regulators * Electrically adjustable mirrors * Mirror heating * Fog lights * Rear window * Driver comfort seat * Seat heating * Longitudinal and transverse differential locks * AP axles * Steel bumper * Amber rotating beacon * High-level air intake * Air dryer * Foldable underride guard * Lane departure warning system * Right-turn assist Djdpfjy R Ixvex Apcewa * Radio * Navigation system * Reversing camera * Roof hatch * Cool box * HydroDrive front axle drive * Steering brake * Finishing brake * 12-speed * Suspension: leaf springs * Payload: 17,870 kg * Endurance brake: electronically controlled engine brake ---- Superstructure: Carnehl 3-way steel pallet tipping body, Jet side boards, Cramaro electric sliding tarpaulin with radio remote control. ---- Exceptionally well-maintained tipper in original condition! Sale to commercial customers only. FOR EXPORT, ONLY THE NET PRICE IS PAYABLE!!!! ALL INFORMATION WITHOUT GUARANTEE, PARTICULARLY REGARDING EQUIPMENT & ACCESSORIES. The basis for all sales contracts, invoices, pro forma invoices, orders, and sales discussions are our terms and conditions (see legal notice for details).

Durum: iyi (kullanılmış), Üretim yılı: 2000, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: 288-40003902, X ekseni hareket mesafesi: 800 mm, Y ekseni hareket mesafesi: 710 mm, Z ekseni hareket mesafesi: 710 mm, masa genişliği: 500 mm, masa uzunluğu: 630 mm, For sale is a DMC 80 H hi-Dyn horizontal machining center with 4 axes. The machine was exclusively used for milling and drilling cast parts for surface finishing. The machine is in very good condition. Technical Specifications Travel distances: X-axis: 800 mm Y-axis: 800 mm Z-axis: 800 mm B-axis: 360° Table data: Table size: approx. 630 × 500 mm Max. workpiece weight: ~1,200–1,400 kg Rotary table: 4th axis, 360° continuous Spindle: Direct drive, liquid-cooled Replaced in 2023/2024 Measuring system: Glass scales Djdpfx Apsytf N Ajcswa Main drive: Max. speed: up to 10,000 rpm Spindle power: approx. 20 kW Torque: S1 – 100% duty cycle Transport dimensions: LxWxH (m): 5.2 x 2.4 x 2.7 Transport weight, machine: 12,500 kg On request, dismantling, loading, and transport can be organized throughout Europe for an additional charge. All prices plus VAT Inspection possible by appointment. Contact us—our team will be happy to assist you. Trade-in or exchange possible! Machinery purchase / sales PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MORE. Do you require a high-quality yet affordable metalworking machine for your production? Or are you looking to sell yours? For more information or contact options, please visit our website.

Durum: ikinci el, kilometre: 211.033 km, güç: 331 kW (450,03 bg), ilk tescil: 03/2016, yakıt türü: dizel, toplam ağırlık: 32.000 kg, dingil konfigürasyonu: 3 aks, bir sonraki muayene (TÜV): 04/2027, frenler: retarder, renk: turuncu, vites türü: otomatik, emisyon sınıfı: Euro 6, yükleme alanı hacmi: 14 m³, yükleme alanı uzunluğu: 5.600 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 1.050 mm, Donanım: ABS, klima, navigasyon sistemi, park ısıtıcısı, * Sun visor * ABS * TCS Traction Control System * Radio * Navigation system * On-board computer * Reversing camera * Cruise control * Air horns * Electric windows * Electrically adjustable mirrors * Mirror heating * Central locking * Fog lights * Roof hatch * Rear window * Driver comfort seat * Seat heating * Longitudinal and transverse differential locks * AP axles * Steel bumper * Amber rotating beacon * Exhaust behind cab * Folding underrun protection Dwodpfxsy Tq Tuj Apcja * Auxiliary heater / Parking heater * Hill-start assist * Cool box * Shunting coupling * 12-speed * Suspension: leaf springs * Payload: 18,060 kg * Retarder (continuous brake) ---Body: Dautel 3-way tipper body for pallets, type DK 4 (rated capacity 24,500 kg), steel sideboard left with Bordmatik, reinforced steel front wall with digger protection, steel rear wall, rear chute, steel floor, lashing eyes, aluminium sideboard right. Sale to commercial customers only. FOR EXPORT, ONLY THE NET PRICE IS PAYABLE! ALL INFORMATION PROVIDED WITHOUT GUARANTEE, ESPECIALLY REGARDING EQUIPMENT AND ACCESSORIES. The basis for all purchase contracts, invoices, pro forma invoices, orders, and sales discussions are our General Terms and Conditions (see imprint).

Durum: ikinci el, kilometre: 211.033 km, güç: 331 kW (450,03 bg), ilk tescil: 03/2016, yakıt türü: dizel, toplam ağırlık: 32.000 kg, dingil konfigürasyonu: 3 aks, bir sonraki muayene (TÜV): 04/2027, frenler: retarder, renk: turuncu, vites türü: otomatik, emisyon sınıfı: Euro 6, yükleme alanı hacmi: 14 m³, yükleme alanı uzunluğu: 5.600 mm, yükleme alanı genişliği: 2.420 mm, yükleme alanı yüksekliği: 1.050 mm, Donanım: ABS, klima, navigasyon sistemi, park ısıtıcısı, * Sun visor * ABS (Anti-lock Braking System) * TCS (Traction Control System) * Radio * Navigation system * On-board computer * Reversing camera * Cruise control * Air horns * Electric windows * Electrically adjustable mirrors * Mirror heating * Central locking * Fog lights * Roof hatch * Rear window * Driver comfort seat * Seat heating * Longitudinal and cross locks * AP axles * Steel bumper * Rotating beacon, orange * Exhaust behind cab * Folding underrun protection * Auxiliary heating * Hill start assist * Cool box * Shunting coupling * 12-speed transmission * Suspension: leaf springs * Payload: 18,060 kg * Permanent brake: retarder ----Body: Dautel 3-way pallet tipper body type DK 4 (nominal load 24,500 kg), steel side wall on the left with Bordmatik, reinforced steel front wall with digger guard, steel rear wall, discharge chute at the rear, steel floor, lashing eyes, aluminum side wall on the right. Sale only to commercial customers. FOR EXPORT ONLY THE NET PRICE IS PAYABLE!!!! ALL INFORMATION WITHOUT GUARANTEE, INCL. EQUIPMENT AND ACCESSORIES. The basis of all purchase contracts, invoices, pro forma invoices, orders, and sales discussions are our general terms and conditions (see legal notice). Dedey Tq Tzspfx Apcjwa

Durum: mükemmel (kullanılmış), Fırsat: CNC 4 eksenli makine, takım değiştirici ve testere ünitesi ile birlikte. Dedpfx Apjyrka Decewa

Durum: yeni, azami yük ağırlığı: 36.040 kg, toplam ağırlık: 53.000 kg, dingil konfigürasyonu: 3 dingil, toplam genişlik: 2.540 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Equipment excerpt. Full specification upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, approx. 3,750 mm long * Gooseneck hydraulically lift/lowerable and detachable * For tractor units: 6x4 or 8x4 Lowbed: * Lowbed with external beams, extendable in SUPER LOW design, approx. 8,000 mm long * Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking * Supply lines are protected within the extendable beams and automatically adjust to the lowbed length * 7 pairs of lashing rings foldable outward (LC 10,000 daN) * 6 pairs of threaded blocks on the inner girder for mounting screw-on RUD rings Rear Undercarriage: * Rear chassis with closed outer frame and checker plate cover * Chassis with excavator trough, closed in the rear half to accommodate air tanks * 3 pairs of lashing rings foldable outward (LC 5,000 daN) * 1 pair of lashing rings foldable outward (LC 10,000 daN) * 1 pair of flat lashing rings, front and rear of the chassis (LC 10,000 daN) Axles: Dwsdjy Uwu Iepfx Apcja * BPW axles and suspension, all axles hydromechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve Tyres: * Tyres 245/70 R 17.5 3PMSF – manufacturer of choice. Load index (146/146F) Brake System: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: * HRM-metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for optimal corrosion protection * Final coating with 2 layers of 2K topcoat, single colour in RAL 3002 Carmine Red as per RAL system 841GL Including accessories: * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized connection bar at the front * Remote steering from front and rear via cable remote control with push buttons, including single-track axle control (without installation in the tractor unit) * Prepared for bolt-on container positioning for 1 x 20', 1 x 40', or 1 x 45' container on the outer beams. No container locks * Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings * Electro-hydraulic power unit * Spiral cable for supplying the electro-hydraulic power unit and/or electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between semi-trailer and tractor unit with plug connection (NATO-NATO) * Yellow reflective tape to EU regulations on sides, extension and rear of the trailer * At the gooseneck and rear, left and right, a bracket for warning signs including a socket * Manual and description on USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable guard around the pumps * 7 pairs of threaded blocks between the lashing rings under the top flange on the outer beam for mounting screw-on RUD rings VLBG-4 * 2nd ride height, approx. 50 mm above normal ride height, adjustable by hand control * On the gooseneck, plug-in aluminium side and rear walls, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in stanchions are removable (body length approx. 2,560 mm) * On the gooseneck, a separate air connection with air gun * 1 stainless steel toolbox, approx. 1,350 x 400 x 400 mm, mounted externally

Durum: ikinci el, azami yük ağırlığı: 37.530 kg, toplam ağırlık: 50.000 kg, dingil konfigürasyonu: 3 aks, ilk tescil: 02/2012, bir sonraki muayene (TÜV): 11/2026, toplam genişlik: 3.000 mm, toplam yükseklik: 3.780 mm, Donanım: ABS, * Gooseneck with foldable side walls * Low bed length: 11,950 mm - 15,450 mm * Low bed extendable in stages by 3,500 mm * Low bed width extendable by 460 mm Djdpfsy T Dyzex Apcswa * Hydraulically adjustable loading ramps (split, 2-piece) * Stakes pockets * Wabco SmartBoard * 4 axles with twin tires * 1st axle liftable * 3rd and 4th axle with trailing steering * Wheel chocks ----* Tire size: 235/75R17.5 * Technical gross weight: 58,000 kg * Curb weight: 12,470 kg * Total length: 13,700 - 17,200 mm * Overall width: 2,540 - 3,000 mm * Next safety inspection due: 05/2026 ----Vehicle number: 12062----Subject to errors and prior sale----Advertising and various lettering have been digitally removed.----We are happy to assist you with all formalities involved in purchasing a vehicle, providing support and advice at every step. Simply let us know your requests and suggestions, and we will take care of them for you. Among other services, we can additionally offer the following (subject to surcharge):----* Trade-in of your old vehicle * Technical inspection/certification (HU/SP) * Complete export processing * Financing arrangement * Application for export license plates * Vehicle transfer * Vehicle registration * Recovery and vehicle transport ----Your VTS Team

Durum: ikinci el, azami yük ağırlığı: 21.130 kg, toplam ağırlık: 34.000 kg, dingil konfigürasyonu: 2 dingil, ilk tescil: 10/2024, bir sonraki muayene (TÜV): 11/2026, toplam genişlik: 2.540 mm, toplam yükseklik: 1.980 mm, Donanım: ABS, Kässbohrer SLL 2-axle low bed trailer with hydraulic steering Highlight: Optionally available for rent as a complete combination together with the truck shown. Manufacturer: Kässbohrer Model / Vehicle code: K.SLL 2 / 2H ? 18 / 20 Vehicle type: Low-bed semi-trailer Country of registration: Germany Brand: Kässbohrer Chassis color: RAL 3020 Traffic Red Dimensions & Weights Overall length: 13,210 mm * Total width: 2,540 mm * Fifth wheel height (H5): 1,250 mm * Platform height (unladen): 910 mm * Platform height (laden): 300 mm * Platform length: 6,810 mm * Extension: 5,550 mm * Gooseneck length: 3,600 mm * Rear swing door: 2,100 mm * Platform thickness: 200 mm * Wheelbase: 10,530 mm * Axle spacing: 1,360 mm * Unladen weight: approx. 12,873 kg (±3%) * Gross weight (40 / 60 / 80 km/h): 42,000 kg * Total axle load: 24,000 kg * Permissible kingpin load: 18,000 kg (40 / 60 / 80 km/h) Dwsdpfx Apoycnbaocja ----Chassis & Axles • 2 axles • 2 hydraulically steered axles • Axles: BPW • Suspension: Air suspension • Suspension travel: 260 mm (190 mm / -70 mm) • Additional lifting of driving level by 40 mm available • Load gauge for axle load display • Semi-automatic centering of steered axles with warning light sensor ----Braking System • WABCO EBS 2S/2M • ABS (Anti-lock Braking System) • RSS (Roll Stability Support) • Brake system in compliance with UN ECE R13 ----Electrical & Lighting • 24V LED lighting system • 2 × 7-pin + 1 × 15-pin socket • LED brake lights • LED rear and fog lights • Electrical system according to UN ECE R48 & ADR • LED work lights at the rear (2 pcs, reverse-dependent) • LED beacon (1 pc) ----Tires & Rims • Tire size: 245/70 R17.5 • Tires: M+S • 3PMSF (suitable for winter) • Tire pressure monitoring system as per R141 • Number of wheels: 9 complete wheels • Rims: Steel rims (Kässbohrer selection) • Spare wheel holder: 1 pc on gooseneck ----Steering & Operation • Hydraulic steering for both axles • Control panel inside vehicle • Wireless remote control for external steering operation • Multifunctional WABCO Smartboard • Axle load indicator • Suspension control • Tire and brake wear monitoring • Breakdown & system monitoring ----Chassis & Frame • High-tensile steel S700 MC (ISO 1726) • Welded bogie-bed connection • Partial metallization (85% zinc / 15% aluminum) on outer frame & gooseneck • Adjustable and detachable gooseneck • 1 × 2 hydraulic cylinders, 220 bar operating pressure • Kingpin: 2 inch, bolted • Kingpin position: single position ----Platform & Body • 3 removable platforms with hardwood flooring • Dimensions per platform: 100 × 1,300 × 2,115 mm • Weight per platform: 225 kg • 2 lashing rings per platform with 8,000 kg tensile strength each • Platform widening: 225 mm, galvanized • Extension brackets: 12 × 2 pieces, galvanized ----Load securing Lashing rings: • 1 × 2 pcs, 13.4 t on gooseneck • 7 × 2 pcs, 13.4 t • 4 × 2 pcs, 8 t in the low bed • 2 × 2 pcs, 13.4 t • 3 × 2 pcs, 8 t on rear platform Stake pockets: • 6 × 2 pcs in pool (50 × 100 mm) • 3 × 2 pcs at rear (50 × 100 mm) ----Attachments & Accessories • Aluminum front panel gooseneck: 360 × 1,550 mm • Aluminum side walls: 360 × 1,900 mm • Aluminum rear wall: 360 × 2,480 mm • Toolboxes right & left (500 × 350 × 400 mm) • Central lubrication system • Side underrun protection according to ECE R73 • Warn... [Text truncated, please provide the remaining text for completion if needed.]

Durum: yeni, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, toplam genişlik: 2.530 mm, Üretim yılı: 2025, Donanım: ABS, 2-axle self-steering trailer, model M2K-9L * COMPACT steering system * Corrosion protection through powder coating * All mounted components bolted * Conventional wiring * Brackets and attached parts in stainless steel or galvanized * 2 single axles, make: BPW, 10 t with disc brakes, including safety ropes * Air suspension * Aluminum air tank * Bolster model IX, with 1x mechanically telescoping stanchion * Tyres: 275/70 R 22.5 on steel rims * EBS braking system * LED tail lights with integrated triangular reflector * 4x LED work lights (1,800 lumens) * Manual central lubrication * Paintwork: RAL 9011 graphite black * Payload approx. 14,550 kg 2-axle self-steering trailer, model M2K-10B * Differences to M2K-9L: Dwjdpfx Ajgqc Hbepcsa * Leaf suspension * 2 single axles, make: BPW, 12 t with drum brakes, including safety ropes * Bolster model IX, with 1x hydraulically telescoping stanchion * Tyres: 315/80 R 22.5 on steel rims * Electric central lubrication * Payload approx. 14,100 kg 2-axle self-steering trailer, model M2K-10L * Differences to M2K-9L: * 2 single axles, make: BPW, 12 t with drum brakes, including safety ropes * Bolster model IX, with 1x hydraulically telescoping stanchion * Tyres: 315/80 R 22.5 on steel rims * Electric central lubrication * Payload approx. 14,100 kg 2-axle self-steering trailer, model M2R-10L Differences to M2K-9L: * Ratio steering system (4-cylinder) * 2 single axles, make: BPW, 12 t with drum brakes, including safety ropes * Bolster model IX, with 1x hydraulically telescoping stanchion * Tyres: 315/80 R 22.5 on steel rims * Electric central lubrication * Payload approx. 13,965 kg Various optional equipment available. Further information upon request. Illustrations may vary from actual product. All information subject to change without notice. Contact: Niclas Lott Tel.:

Durum: yeni, azami yük ağırlığı: 56.570 kg, toplam ağırlık: 66.500 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, Our complete vehicle stock with immediately and short-term available vehicles can be found on our website. Excerpt from the equipment specification. Complete equipment details available on request. Chassis: * Chassis frame construction made of welded longitudinal beams and inserted cross members * Underrun nose width approx. 700 mm * Fifth wheel plate at least approx. 8 mm thick, positioned between the main beams * Maximum cross member spacing 400 mm (for longitudinally laid floor) * 3.5 inch kingpin according to SAE standard, replaceable * Outer frame as UNP 200, open to the outside Landing legs: * 24 t telescopic landing gear JOST - MODUL CH (Heavy Duty) S-foot Axles: Djdpfxjwx Dctj Apcowa * 4 x 10 t SAF axles with large drum brake * 22.5 single tires * Axle spacings approx. 1,700/1,810/1,810 mm * Air suspension units, each with 10 t load capacity, lifting and lowering device with 1 rotary valve Knorr/Wabco * Mounting bracket for lifting and lowering device, bolted version Brakes: * Smartboard/TIM/Infocenter on the holder for lifting and lowering, in addition to the lifting and lowering valve, without battery (can only be operated with the towing vehicle) * Holder for lights and brakes at the front of the underrun nose, total height approx. 700 mm * Tire pressure monitoring basic version, connected to the EBS CAN bus system * With dual release valve for brake and spring accumulator * Test nipple for brake cylinder pressure on the front right brake cylinder * 1 coupling head each red and yellow * Lifting and lowering device installed at the rear left in driving direction * EBS brake system by Wabco, EBS diagnostics via CAN bus (EBS connector), no external diagnostic cable provided!! Tyres: * 8 x 445/65 R 22.5 – branded manufacturer of our choice * Hub centering Lubrication: * Grease nipple strips on the bogies and at the front on the steering. No central lubrication Body: * Without body certificate according to DIN EN 12642 XL * 2x LED work lamps on top of the front wall (rear-facing), switch on lifting/lowering control bracket * Robust front wall for platform body * Contour markings side yellow, rear yellow * Front wall approx. 800 mm high, with sheet metal cladding, bolted design Lighting system: * 2x LED work lamps, installed in the lamp plate, switched via reverse gear * 2x LED work lamps, switched via reverse gear, 1x per side near landing gear * 2x LED reversing lights per side, 1 mounted before the 1st axle * Lighting/wiring system by manufacturer of our choice * Number plate lighting * The towing vehicle must provide adequate power for the chosen lighting (esp. reversing lights) * Position lights front, bottom, white, 1 each right and left (LED) * 24 volt lighting system with large multifunction lamp * Side marker lights (LED) flashing * 1x 15-pin and 2x 7-pin connectors at the front via multifunction box * EBS socket * 1 pair of lane departure warning lights (LED) Floor: * Hardwood floor approx. 28 mm, alternately with galvanized omega steel profiles Paint/Coating (no metallic colors): * Chassis painted in RAL color of choice, front wall (steel construction) in RAL color of choice * Axle hubs in chassis color * Axles and landing legs black * Wheels in aluminum/silver similar to RAL 9006 * Wheel nuts untreated * Underrun protection painted in RAL 9010 pure white (aluminum) Accessories: * Lifting device for 1st axle * 9 hook plates welded into the outer frame per side, lashing capacity max. 3,000 daN * 12 RUD SLP lashing points per side w

Durum: yeni, azami yük ağırlığı: 45.250 kg, toplam ağırlık: 58.000 kg, dingil konfigürasyonu: 3 aks, toplam genişlik: 2.550 mm, Donanım: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full specification available upon request. Chassis, cranked: * Special steel frame made of high-tensile fine-grain steels, electric-welded at connection points * Well-dimensioned outer frame. 4-axle configuration * Wheel arches above the axles with spray suppression * All steel parts are sandblasted * Side underrun protection made of anodised aluminium installed * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the cranked area for the maximum possible low-bed length in combination with alu-leg drop supports instead of telescopic supports, max. rear swing radius of the tractor unit approx. 2,100 mm Special body with rear stanchion extension: * DINKEL special superstructure * Self-supporting aluminium roof rail/profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stanchions extendable for loading/unloading up to approx. 4,200 mm * Three sliding stanchions per side with rubber tension relief * Additional central stanchion locks in the roof rail and parking position, via pull cable and spring bolt * DINKEL mechanical lifting roof, height-adjustable * Lifting roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the stanchions * Front overlap at the bulkhead for driving operation under tarpaulin up to total height approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminium slats on the sides, lower 450 pockets, above it 4 single row pockets. In the high bed only 3 rows of slats, evenly distributed gaps Floor: * Approx. 27 mm specially water-resistant bonded beech plywood, anti-slip surface * Steel plate in wheel arch area, fork-lift truck suitable as per DIN standard * Outer frame surface flush Brakes: * WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with odometer and axle load display * Incl. WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF drum-braked axles in low-loader configuration * Air suspension with lift and lower facility, total stroke approx. 230 mm Dwjdpfowx Dbiox Apcoa * Third and fourth axle as friction-steered trailing axles with electric and mechanical locking Twin tyres: * 235/75 R 17.5, 16-ply. Brand of our choice, incl. spare wheel holder * Without spare wheel Lighting: * According to EC standard including LED side marker lights * Position lamps in LED version * 2 additional reversing lights * 2 working lights, inside on front wall, upper side Paintwork: * Chassis and superstructure painted in solid RAL 3002 carmine red * Centre stanchions, axles KTL-coated black * Corner stanchions hot-dip galvanised * Plastic parts black * Galvanised parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply line * Air suspension in ECAS version, operation on the trailer * Oversize signs front and rear in galvanised, infinitely telescopic version, with mounted marker lights including base sockets for rotating beacons (small panels) * Additional unlocking of sliding roof frame from outside * 4 stanchion adapters for special outer frame profile, for securing centre stanchions as desired * PVC sliding tarpaulins, col

Üretim yılı: 2001, durum: işlem için hazır (kullanılmış), Biesse Rover 22 CNC işleme merkezi Üretim yılı 2001 SN 07498 Çalışma aralığı 4 eksen X ekseni 3060 mm Y ekseni 1080 mm Z ekseni 155 mm 6 konsol 18 vakumlu bardak tutuculu Merdaneyi kaldırmak için 4 pnömatik bakalit çubuk Dikey elektro mil 7, Otomatik takım değiştirme ile 5 kW, ISO 30 konik Otomatik takım değiştirme Çalışma kafasında 7 konum Aşağıdaki şekilde düzenlenmiş 20 iğ ile delme kafası: X ekseninde 7 dikey Y ekseninde 7 dikey X ekseninde 2 yatay Y'de -axis Kanal açma testeresi 120mm Emniyet sırtlı paspaslar 110 m3 / h vakum pompası CE işaretli Ağırlık 3500 Kg Teknik özellikler değişebilir Dwjdpfx Aoggxihopcoa

Durum: mükemmel (kullanılmış), Üretim yılı: 1995, hala korunmuş CNC çünkü çok az kullanılıyor Dsdsig T Epspfx Apcswa kapı üretimi için kullanılmıştır, ancak herhangi bir amaç için kullanılabilir. Çift tablalı, sol ve sağ taraftan monte edilebilir 4 eksen x 5000 mm y 1350 mm z 450 mm a 190° Ana iş mili SK 40 8 kw su soğutmalı 17 000 rpm'ye kadar 24 konumlu zincir magazini

Durum: iyi (kullanılmış), ilk tescil: 10/2007, toplam uzunluk: 10.500 mm, toplam genişlik: 2.550 mm, toplam yükseklik: 880 mm, renk: sarı, Üretim yılı: 2007, Boş ağırlık: 6.600 kg Yük kapasitesi: 23.400 kg Toplam ağırlık: 30.000 kg Yükleme platformunun yüksekliği: 88 cm Teknik durumu: iyi Görsel durumu: iyi Goldhofer TU 3-24/80 3 akslı, alçak platformlu römork Üretici: Goldhofer Tip: TU 3-24/80 Model: 3 akslı, alçak platformlu römork Teknik yük kapasitesi: 30.000 kg Kendi ağırlığı: 6.600 kg Çeki demiri: 50 mm Araç açıklaması Donanım * 3 akslı Goldhofer alçak platformlu römork * Sağlam ve burulmaya dayanıklı çerçeve yapısı * Kısmen hidrolik olarak çalıştırılan rampa * BPW akslar * Yaylı akslar * 50 mm çeki demiri * Güvenli nakliye için düşük yükleme yüksekliği * Profesyonel ağır yük ve makine taşımacılığı için ideal Boyutlar * Yükleme platformunun uzunluğu: 830 cm * Yükleme platformunun genişliği: 255 cm * Her iki tarafta 21,5 cm genişletilebilir * Maksimum yükleme platformu genişliği (genişletilmiş halde): 298 cm * Yükleme platformunun yüksekliği: 88 cm Rampa * Kısmen hidrolik olarak çalıştırılabilir * Rampa uzunluğu: 365 cm * Rampa genişliği: Her rampa için 80 cm * Çelik paletli makineler ve tekerlekli makineler için uygundur * Güvenli yükleme ve boşaltma için düşük rampa açısı ### Teknik veriler * Akslar: BPW * Süspansiyon: Yaylı süspansiyon * Kendi ağırlığı: 6.600 kg * Teknik yük kapasitesi: 30.000 kg * Günlük profesyonel kullanım için sağlam yapı Kullanım alanları Goldhofer TU 3-24/80, aşağıdakilerin taşınması için mükemmeldir: Dwodpezlfbuefx Apcoa * Ekskavatörler * Tekerlekli yükleyiciler * Dozerler * Mobil vinçler * Platformlu asansörler * Yol inşaat makineleri * Tarım makineleri * Endüstriyel makineler * Konteynerler ve diğer ağır araçlar ve ekipmanlar Sizi, römorkun ücretsiz bir şekilde incelenmesi için davet ediyoruz.

Durum: ikinci el, boş ağırlık: 6.350 kg, azami yük ağırlığı: 23.650 kg, toplam ağırlık: 30.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 09/2005, yükleme alanı uzunluğu: 6.800 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 900 mm, toplam uzunluk: 2.550 mm, toplam genişlik: 3.500 mm, süspansiyon: çelik, lastik boyutu: 235/75R17.5, renk: turuncu, kilometre: 1.001 km, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, Araç konumu: Bovenden, 3 dingil, BPW dingilleri, döner tabla, yaprak süspansiyon, ABS (kilitlenme önleyici sistem), bağlama halkaları, mekanik rampalar, arka destek, yan alüminyum yan koruma, ikiz lastik, alet sandığı Üst yapı: Mekanik rampalı, 3 dingilli alçak şasi treyler. Dsdoy Efdlepfx Apcswa AKSESUAR BİLGİLERİ GARANTİSİZ OLUP, değişiklik, ara satış ve hata yapma hakkı saklıdır!

Durum: ikinci el, azami yük ağırlığı: 18.000 kg, toplam ağırlık: 24.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 12/1991, yükleme alanı uzunluğu: 8.200 mm, yükleme alanı genişliği: 2.500 mm, Donanım: ABS, * ABS * BPW axles Dedpfx Apswdb Ttscjwa ----Body: Low-bed trailer (2200 + 6000 mm), loading height approx. 900 mm, rear sloped, drive-on height approx. 750 mm, steel/wooden floor, extendable to 3 m, spring-assisted loading ramps, lashing rings. Sale exclusively to businesses. FOR EXPORT, ONLY THE NET PRICE IS PAYABLE! ALL INFORMATION PROVIDED WITHOUT GUARANTEE, ESPECIALLY REGARDING EQUIPMENT & ACCESSORIES. Our General Terms and Conditions (see legal notice) form the basis of all purchase agreements, invoices, pro forma invoices, orders, and sales discussions.

Durum: ikinci el, boş ağırlık: 9.600 kg, azami yük ağırlığı: 38.400 kg, toplam ağırlık: 48.000 kg, dingil konfigürasyonu: 3 dingil, ilk tescil: 10/2012, yükleme alanı uzunluğu: 8.800 mm, yükleme alanı genişliği: 2.500 mm, yükleme alanı yüksekliği: 860 mm, renk: gümüş, Üretim yılı: 2009, vites türü: diğer, şoför kabini: diğer, Donanım: ABS, * German trailer * 1st hand * Condition, see photos * Low loader Goldhofer, type STN-L3-39/80 * 3-axle low loader with extra-long ramps * Ramps hydraulically operated and laterally adjustable * Loading length 8.80 m x 2.50 m Dwedpfx Apowxm Ilecoa * Loading height 0.85 m * SKF axles * 2 support legs * Steering trailing axle * Leaf/air suspension with lifting/lowering function * Heavy-duty DIN lashing eyes * EBS * ABS (anti-lock braking system) * Storage box * Twin tires * Permissible gross weight up to 48,000 kg * Unladen weight 9,600 kg * Payload 38,400 kg If a new TÜV inspection is desired, we are happy to offer a quote from our partner workshops. Our offer is generally WITHOUT new TÜV inspection, without new DGUV, without new SP, and without new UVV. You can find more trucks on our website at We speak the following languages: German, English, Polish, Turkish Note: We offer and strongly recommend an inspection and examination of the goods to avoid any misunderstandings regarding condition or suitability on the buyer’s side. Viewing and inspection are possible at any time by appointment and are expressly encouraged. All details are without guarantee. We accept no liability for errors or incorrect information in the offer. The buyer is required to independently verify the condition and equipment of the goods/vehicles. Subject to change, prior sale, and errors.

Durum: yeni, yükleme alanı uzunluğu: 8.000 mm, yükleme alanı genişliği: 1.350 mm, yükleme alanı yüksekliği: 450 mm, renk: kırmızı, Üretim yılı: 2024, Color: Red Hersteller: Goldhofer Typ: Raupenbett / Spinebed BB 450 A Fahrgestellnummer: 2100788 Baujahr: 2024 – NEU / unbenutzt Allgemeines Ausziehbar, von 8.000 mm bis 13.000 mm Nutzlastklasse 100t / 120t in Kombination 4+6 Bauhöhe 450 mm; Länge 8.000 mm, Breite 1.350 mm Verlängerbar in 500-mm-Schritten Hinten Zurrkupplung zur Verbindung mit THP-Fahrwerken Vorne Klauenkupplungen für die Verbindung mit Sattelhals oder Klauenkupplungsadapter Integrierte Versorgungsleitungen für Hydraulik, Bremse und Elektrik mit Anschlusskupplungen Eigengewicht ca. 14.400 kg Ladungssicherung 1 Paar Zurrösen (LC = 30.000 daN) im hinteren Kupplungskopf 8 Paar Zurrösen (LC = 20.000 daN) außen am Außenholm angeordnet Seitliche Erweiterungen Ausklappbare Abstützungen und Einlagen am Außenholm (Grundlänge) Ausklappbare Seitenerweiterungen und Matratzen im Innentubus 1 x Schnellkupplungsadapter THP/SL Zur Verbindung der Kupplungskrallen eines Decks mit den Kuppellaschen eines modularen Fahrwerks oder eines Sattelhalses Eigengewicht 1.600 kg 1 x Auffahrkeil für Baggerbett in Stahl-Ausführung (4 Stück) Gewicht 360 kg = Weitere Informationen = Allgemeine Informationen Baujahr: 2024 Gewichte Leergewicht: 14.400 kg Nutzlast: 120.000 kg zul. Gesamtgewicht: 134.400 kg Funktionell Ladeflächenhöhe: 45 cm Aufbau ausziehbar: Ja Zustand Allgemeinzustand: sehr gut Technischer Zustand: sehr gut Optischer Zustand: sehr gut Finanzielle Informationen Dwedpfx Apevnb Nwjcsa Preis: auf Anfrage

Durum: ikinci el, kilometre: 715.000 km, güç: 301 kW (409,25 bg), ilk tescil: 12/2003, yakıt türü: dizel, boş ağırlık: 8.400 kg, azami yük ağırlığı: 9.600 kg, toplam ağırlık: 18.000 kg, dingil konfigürasyonu: 2 dingil, yakıt: biyodizel, renk: diğer, şoför kabini: diğer, vites türü: mekanik, emisyon sınıfı: hiçbiri, süspansiyon: hava, Donanım: ABS, basınçlı hava freni, diferansiyel kilidi, düşük ses seviyesi, hız sabitleyici, tır çekici bağlantısı, For swap bodies 7.15 and 7.45 m, -- Errors in printing, mistakes, and alterations reserved, sample images --, More data at: !, More details: ! Djdpeztnuajfx Apcowa

Durum: onarım gereklidir (kullanılmış), Üretim yılı: 2017, Fonksiyonellik: çalışmıyor, makine/araç numarası: 109238, Caracteristici tehnice: Zona de lucru # Diametru mandrină: 260 mm # Greutate maximă: 150 kg # Diametru max. piesă prelucrabilă: 280 mm Dwodjxxkgpspfx Apcsa # Diametru/înălţime max. piesă: 200/200 mm # Cursă X (cursă de lucru): 760 mm / Viteză rapidă pe X: 60 m/min / Forţă de avans: 6,9 kN # Cursă Z: 415 mm / Viteză rapidă pe Z: 30 m/min / Forţă de avans: 18,7 kN # Timp de încărcare: 5÷6 sec # Automatizare standard complet închisă (număr de cuiburi de încărcare la un anumit diametru al piesei: 14/(80...200), 18/(30...160), 30/(30...85)) Broşă principală # Arbore principal conform DIN 55026: Mărimea 6 # Turaţie maximă: 4500 rpm # Putere cu factor de serviciu 100/40%: 25/18 kW # Cuplu la factor de serviciu 100/40%: 280/200 Nm Portscule cu scule motorizate # Suporturi cu coadă cilindrică conform DIN 69880: 12 - BMT65 # Număr de posturi: 12 # Lungime maximă sculă inclusiv portsculă: 200 mm # Turaţie maximă: 6000 rpm # Cuplu maxim la ciclu de serviciu 10%: 27 Nm, ciclu 100%: 14 Nm Echipament electric # Tensiune de operare: 400 - 480 V, 100 A # Putere instalată: 36 kVA Dimensiuni # Dimensiuni totale: Lungime = 5300 mm (cu evacuator de aşchii), Lăţime = 2300 mm, Înălţime = 3650 mm # Greutate: 9000 kg Caracteristici şi capabilităţi principale: # Configuraţie verticală: Evacuare optimă a aşchiilor şi încărcare/descărcare facilă. # Sistem de comandă: GE Fanuc FS 32i B. # Precizie ridicată: Acurateţe la poziţionare pe axe X,Z de ±0,001 mm (rigle liniare Heidenhain) # Arbore principal: Putere mare şi plajă largă de turaţii. # Control în proces: Palpator de măsurare Marposs T25 # Încărcare/descărcare automată: Piese tip O Emag alimentate şi evacuate prin automatizarea integrată. # Scule motorizate: Permite operaţiuni de găurire şi frezare suplimentare. # Transportor de aşchii, unitate de răcire, filtru dublu cu cartuş interschimbabil, pompă presiune înaltă 15 bar # Monitorizare durată de viaţă scule cu gestionare "sister tool" # Zonă de lucru complet închisă, iluminată # Documentaţie: Electronic disponibilă, varianta tipărită incompletă Stare maşină: NU FUNCŢIONEAZĂ # Convertizor motor electric hidraulic # Motor sculă motorizată

Durum: ikinci el, Üretim yılı: 2017, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: 109242, Caracteristici tehnice: Zonă de lucru # Diametru mandrină: 260 mm # Greutate maximă: 150 kg # Diametru de rotație: 280 mm # Diametru/înălțime piesă max.: 200/200 mm # Cursă X (cursă de lucru): 760 mm / Viteză rapidă pe X: 60 m/min / forță de avans: 6,9 kN # Cursă Z: 415 mm / Viteză rapidă pe Z: 30 m/min / forță de avans: 18,7 kN # Timp încărcare: 5÷6 sec # Automatizare închisă standard (număr de cuiburi de încărcare în funcție de diametrul piesei: 14/(80...200), 18/(30...160), 30/(30...85)) Broșă principală # Broșă conform DIN 55026: Dimensiune 6 # Turație maximă: 4500 rpm # Putere la ciclu de funcționare 100/40%: 25 / 18 kW # Cuplu la ciclu de funcționare 100/40%: 280 / 200 Nm Portscule cu scule acționate # Suporturi cilindrice conform DIN 69880: 12 - BMT65 # Număr de poziții: 12 # Lungime maximă sculă inclusiv suport: 200 mm # Turație maximă: 6000 rpm # Cuplu maxim la regim de 10%: 27 Nm, la regim de 100%: 14 Nm Echipament electric # Tensiune de operare: 400 - 480 V, 100 A # Putere instalată: 36 kVA Dimensiuni # Dimensiuni totale: Lungime=5300 mm cu transportor de șpan, Lățime=2300 mm, Înălțime=3650 mm Dwedpfx Aoxxit Ujpcja # Greutate: 9000 kg Caracteristici și capabilități principale: # Construcție verticală: Evacuare optimă a șpanului și facilitarea încărcării/descărcării. # Sistem de comandă: GE Fanuc FS 32i B. # Precizie ridicată: Precizia de poziționare pe axele X, Z este de ±0,001 mm cu rigle liniare Heidenhain # Broșă principală: Putere ridicată și interval larg de turații. # Control în proces: palpator Marposs T25 # Manipulare automată a pieselor: Emag O-Type - piesele sunt livrate și evacuate de la mașină prin automatizare integrată. # Scule acționate: Posibilitatea de utilizare a sculelor cu comandă extinde gama de prelucrări (găurire/frezare). # Monitorizare durată de viață sculă cu management scule pereche (sister tool). # Transportor de șpan și unitate de filtrare lichid de răcire – filtru "micron" cu "filtru de hârtie" și pompe de 40 Bar (pot filtra pentru 2 mașini) # Zonă de lucru complet carcasată, iluminare în zona de lucru # Documentație: electronică disponibilă; carte incompletă Stare utilaj: ÎN FUNCȚIUNE

Durum: ikinci el, Üretim yılı: 2017, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: 109239, Caracteristici tehnice: Zona de lucru # Diametru mandrină: 260 mm # Greutate max.: 150 kg # Diametru de strunjire: 280 mm # Diametru/înălțime piesă: max. 200/200 mm # Cursă X (cursă de lucru): 760 mm / Viteză rapidă pe X: 60 m/min / Forță de avans: 6,9 kN # Cursă Z: 415 mm / Viteză rapidă pe Z: 30 m/min / Forță de avans: 18,7 kN # Timp de încărcare: 5÷6 sec # Automatizare închisă standard (număr de cuiburi de încărcare cu diametrul piesei: 14/(80...200),18/(30...160),30/(30...85)) Broșă principală # Conform DIN 55026: mărimea 6 # Turație maximă: 4500 rpm # Putere la ciclu de lucru 100/40%: 25/18 kW # Cuplu la ciclu de lucru 100/40%: 280/200 Nm Portscule cu scule motorizate # Suporturi tijă cilindrică conform DIN 69880: 12 - BMT65 # Număr poziții: 12 # Lungime maximă sculă cu portsculă: 200 mm # Turație maximă: 6000 rpm # Cuplu maxim la 10% ciclu: 27 Nm, la 100% ciclu: 14 Nm Echipament electric # Tensiune de operare: 400 - 480 V, 100 A # Putere instalată: 36 kVA Dimensiuni # Dimensiuni totale: Lungime=5300 mm (cu evacuator de șpan), Lățime=2300 mm, Înălțime=3650 mm Dwedpfxexxir Do Apcoa # Greutate: 9000 kg Caracteristici principale și capacități: # Construcție verticală: Evacuare optimă a șpanului și încărcare/descărcare facilă # Comandă: GE Fanuc FS 32i B # Precizie ridicată: Precizie de poziționare pe axe X, Z ±0,001 mm, rigle liniare Heidenhain # Broșă principală: Putere ridicată și interval larg de turații # Control proces: Sondă de măsurare Marposs T25 # Încărcare/descărcare automată: Piese tip Emag O, alimentare și evacuare automată integrată # Scule motorizate: Posibilitate de găurire și frezare, extindere gamă prelucrare # Monitorizare durată de viață scule și management scule gemene # Transportor de șpan și unitate de filtrare lichid de răcire cu filtru micron și filtru de hârtie, pompe 40 bar (poate deservi 2 mașini) # Zonă de lucru complet închisă; iluminare în zona de lucru # Documentație: Electronică completă & carte incompletă Stare utilaj: ÎN FUNCȚIUNE

Durum: ikinci el, Üretim yılı: 2015, Fonksiyonellik: tamamen fonksiyonel, makine/araç numarası: 106679, Caracteristici tehnice: Zona de lucru # Diametru mandrină: 260 mm # Greutate maximă: 150 kg # Diametru de strunjire: 280 mm # Diametru/înălțime piesă max.: 200/200 mm # Cursă X (cursă de lucru): 760 mm / Viteză rapidă pe X: 60 m/min / forță de avans: 6,9 kN # Cursă Y: +/-30 mm / Viteză rapidă pe Y: 15 m/min / forță de avans: 7,5 kN # Cursă Z: 415 mm / Viteză rapidă pe Z: 30 m/min / forță de avans: 18,7 kN # Timp de încărcare: 5÷6 sec # Automatizare închisă standard (număr de cuiburi de încărcare în funcție de diametrul piesei: 14/(80...200), 18/(30...160), 30/(30...85)) Arbore principal # Arbore conform DIN 55026: mărimea 6 # Turație maximă: 4.500 rpm # Putere la ciclu de funcționare 100 / 40%: 25 / 18 kW # Cuplu la ciclu de funcționare 100 / 40%: 280 / 200 Nm Portscule cu scule motorizate # Suporturi prindere cilindrică conform DIN 69880: 12 - BMT65 # Număr de poziții: 12 # Lungime maximă sculă inclusiv portsculă: 200 mm # Turație maximă: 6.000 rpm # Cuplu maxim la ciclu 10%: 27 Nm, la ciclu 100%: 14 Nm Echipament electric # Tensiune de lucru: 400 - 480 V, 100 A Dwsdoxw Smbepfx Apcja # Putere instalată: 36 kVA Dimensiuni # Dimensiuni totale: Lungime = 5.300 mm cu extractor de așchii, Lățime = 2.300 mm, Înălțime = 3.650 mm # Greutate: 9.000 kg Caracteristici și capabilități principale: # Construcție verticală: Evacuare optimă a așchiilor și încărcare/descărcare facilă # Control: GE Fanuc FS 32i B # Precizie ridicată: Precizie de poziționare pe axele X, Z ±0,001 mm cu rigle liniare Heidenhain # Arbore principal: Putere mare și domeniu larg de turații # Control în proces: palpator de măsurare Marposs T25 # Încărcare/descărcare automată: Tip O Emag - piesele sunt alimentate și evacuate automat # Scule motorizate: Extind domeniul de prelucrare pentru operațiuni de găurire/frezare # Monitorizare durată de viață scule cu management scule pereche # Bandă transportoare așchii și unitate de filtrare răcire Micronfilter cu filtru de hârtie, pompe 40 Bar (poate filtra două mașini) # Zonă de lucru complet închisă, cu iluminare # Documentație: electronic disponibilă & carte necompletă Stare utilaj: FUNCȚIONAL